|
发表于 2010-9-20 14:41:53
|
显示全部楼层
这个是基本配置,,如须要做DHCP去找一下DHCP配置吧
/interface ethernet set ether1 name=lan
/interface ethernet set ether2 name=wan1
/interface ethernet set ether3 name=wan2
/ip address add address=192.168.1.1/24 interface=lan comment=lan
/ip dns set primary-dns=xxx.xxx.xxx.xxx secondary-dns=xxx.xxx.xxx.xxx allow-remote-requests=yes
/ip firewall mangle add chain=forward protocol=tcp tcp-flags=syn action=change-mss new-mss=1440
/interface pppoe-client add name="pppoe-out1" interface=wan1 user="账号1" password="密码1" add-default-route=no disabled=no
/interface pppoe-client enable pppoe-out1
/ip address add address=58.58.58.1/32 interface=pppoe-out1 comment="1"
/ip route add gateway=58.58.58.1 routing-mark=1 comment="1"
/ip firewall mangle add chain=prerouting src-address=192.168.1.0/24 connection-state=new nth=1,1,0 action=mark-connection new-connection-mark=1 passthrough=yes disabled=no
/ip firewall mangle add chain=prerouting src-address=192.168.1.0/24 connection-mark=1 action=mark-routing new-routing-mark=1 passthrough=no disabled=no
/ip firewall nat add chain=srcnat connection-mark=1 action=src-nat to-addresses=58.58.58.1 to-ports=0-65535 comment="1" disabled=no
/interface pppoe-client add name="pppoe-out2" interface=wan2 user="账号2" password="密码2" add-default-route=no disabled=no
/interface pppoe-client enable pppoe-out2
/ip address add address=58.58.58.2/32 interface=pppoe-out2 comment="2"
/ip route add gateway=58.58.58.2 routing-mark=2 comment="2"
/ip firewall mangle add chain=prerouting src-address=192.168.1.0/24 connection-state=new nth=1,1,1 action=mark-connection new-connection-mark=2 passthrough=yes disabled=no
/ip firewall mangle add chain=prerouting src-address=192.168.1.0/24 connection-mark=2 action=mark-routing new-routing-mark=2 passthrough=no disabled=no
/ip firewall nat add chain=srcnat connection-mark=2 action=src-nat to-addresses=58.58.58.2 to-ports=0-65535 comment="2" disabled=no
最后在添加更新网关脚本
在/system Sheduler 里添加下面的脚本,同时把Intervan时间改成30秒
:local assign-address
:local new-address
:local status
:local x
:set x 2
:for i from=1 to=$x do={
:set status [/interface get [/interface find name=("pppoe-out" . $i)] running]
:if ($status=true) do={
:set new-address [/ip address get [/ip address find dynamic=yes interface=("pppoe-out" . $i)] address]
:set new-address [:pick $new-address 0 ([:len $new-address] -3)]
:set assign-address [/ip address get [/ip address find dynamic=no interface=("pppoe-out" . $i)] address]
:set assign-address [:pick $assign-address 0 ([:len $assign-address] -3)]
:if ($assign-address != $new-address) do={ /ip address set [/ip address find comment=$i] address=$new-address network=$new-address
broadcast=$new-address
/ip route set [/ip route find comment=$i] gateway=$new-address
/ip fir nat set [/ip fir nat find comment=$i] to-addresses=$new-address
/ip route set [/ip route find comment=$i] gateway=$new-address
}
}
}
如须做动太限速PCQ可以去论坛里找找吧~~ |
|