发一个菜鸟级的无线配置

shjj8381981

# oct/16/2006 17:39:14 by routeros 2.9.27
# software id = V0WL-FLT
#
/ interface ethernet
set lan name="lan" mtu=1500 mac-address=**:**:4C:81:C4:** arp=enabled \
    disable-running-check=yes auto-negotiation=yes full-duplex=yes \
    cable-settings=default speed=100Mbps comment="" disabled=no
set ether2 name="ether2" mtu=1500 mac-address=**:**:E9:18:B1:** arp=enabled \
    disable-running-check=yes auto-negotiation=yes full-duplex=yes \
    cable-settings=default speed=100Mbps comment="" disabled=yes
set internat name="internat" mtu=1500 mac-address=**:**:B7:9C:BB:** \
    arp=enabled disable-running-check=yes auto-negotiation=yes full-duplex=yes \
    cable-settings=default speed=100Mbps comment="" disabled=no
/ interface wireless
set wlan name="wlan" mtu=1500 mac-address=**:**:7F:1F:36:** arp=enabled \
    disable-running-check=no radio-name="20037F1F****" mode=ap-bridge \
    ssid="MikroTik" area="" frequency-mode=superchannel country=china \
    antenna-gain=0 frequency=2467 band=2.4ghz-b/g scan-list=default \
    rate-set=default supported-rates-b=1Mbps,2Mbps,5.5Mbps,11Mbps \
    supported-rates-a/g=6Mbps,9Mbps,12Mbps,18Mbps,24Mbps,36Mbps,48Mbps,54Mbps \
    basic-rates-b=1Mbps basic-rates-a/g=6Mbps max-station-count=2007 \
    ack-timeout=dynamic tx-power-mode=default noise-floor-threshold=default \
    periodic-calibration=default periodic-calibration-interval=60 \
    burst-time=disabled dfs-mode=none antenna-mode=ant-a wds-mode=disabled \
    wds-default-bridge=none wds-default-cost=100 wds-cost-range=50-150 \
    wds-ignore-ssid=no update-stats-interval=disabled \
    default-authentication=yes default-forwarding=yes default-ap-tx-limit=0 \
    default-client-tx-limit=0 proprietary-extensions=post-2.9.25 hide-ssid=no \
    security-profile=profile1 disconnect-timeout=3s on-fail-retry-time=100ms \
    preamble-mode=both compression=no allow-sharedkey=no comment="" \
    disabled=no
/ interface wireless nstreme
set wlan enable-nstreme=no enable-polling=yes framer-policy=none \
    framer-limit=3200
/ interface wireless manual-tx-power-table
set wlan manual-tx-powers=1Mbps:17,2Mbps:17,5.5Mbps:17,11Mbps:17,6Mbps:17,9Mbps\
    :17,12Mbps:17,18Mbps:17,24Mbps:17,36Mbps:17,48Mbps:17,54Mbps:17
/ interface wireless security-profiles
set default name="default" mode=none authentication-types="" \
    unicast-ciphers="" group-ciphers="" wpa-pre-shared-key="" \
    wpa2-pre-shared-key="" eap-methods=passthrough tls-mode=no-certificates \
    tls-certificate=none static-algo-0=none static-key-0="" static-algo-1=none \
    static-key-1="" static-algo-2=none static-key-2="" static-algo-3=none \
    static-key-3="" static-transmit-key=key-0 static-sta-private-algo=none \
    static-sta-private-key="" radius-mac-authentication=no group-key-update=5m
add name="profile1" mode=static-keys-required \
    authentication-types=wpa-psk,wpa2-psk unicast-ciphers=tkip \
    group-ciphers=tkip wpa-pre-shared-key="" wpa2-pre-shared-key="" \
    tls-mode=no-certificates tls-certificate=none static-algo-0=40bit-wep \
    static-key-0="1111111111" static-algo-1=none static-key-1="" \
    static-algo-2=none static-key-2="" static-algo-3=none static-key-3="" \
    static-transmit-key=key-0 static-sta-private-algo=none \
    static-sta-private-key="" radius-mac-authentication=no group-key-update=5m
/ interface wireless align
set frame-size=300 active-mode=yes receive-all=no \
    audio-monitor=00:00:00:00:00:00 filter-mac=00:00:00:00:00:00 ssid-all=no \
    frames-per-second=25 audio-min=-100 audio-max=-20
/ interface wireless snooper
set multiple-channels=yes channel-time=200ms receive-errors=no
/ interface wireless sniffer
set multiple-channels=no channel-time=200ms only-headers=no receive-errors=no \
    memory-limit=10 file-name="" file-limit=10 streaming-enabled=no \
    streaming-server=0.0.0.0 streaming-max-rate=0
/ interface l2tp-server server
set enabled=no max-mtu=1460 max-mru=1460 \
    authentication=pap,chap,mschap1,mschap2 default-profile=default-encryption
/ interface pppoe-server server
add service-name="service1" interface=wlan max-mtu=1492 max-mru=1492 \
    authentication=chap,mschap1,mschap2 keepalive-timeout=disabled \
    one-session-per-host=yes max-sessions=0 default-profile=default \
    disabled=no
/ interface pptp-server server
set enabled=no max-mtu=1460 max-mru=1460 authentication=mschap1,mschap2 \
    keepalive-timeout=30 default-profile=default-encryption
/ ip pool
add name="hlw" ranges=192.168.2.0/24
add name="wlan" ranges=192.168.3.0/24
/ ip telephony region
/ ip telephony gatekeeper
set gatekeeper=none remote-id="" remote-address=0.0.0.0
/ ip telephony aaa
set use-radius-accounting=no interim-update=0s
/ ip telephony codec
move G.711-uLaw-64k/sw
move G.711-ALaw-64k/sw
move G.729A-8k/sw
move G.729-8k/sw
move G.723.1-6.3k/sw
move GSM-06.10-13.2k/sw
move LPC-10-2.5k/sw
/ ip accounting
set enabled=no account-local-traffic=no threshold=256
/ ip accounting web-access
set accessible-via-web=no address=0.0.0.0/0
/ ip service
set telnet port=23 address=0.0.0.0/0 disabled=yes
set ftp port=21 address=0.0.0.0/0 disabled=yes
set www port=80 address=0.0.0.0/0 disabled=no
set ssh port=22 address=0.0.0.0/0 disabled=yes
set www-ssl port=443 address=0.0.0.0/0 certificate=none disabled=yes
/ ip upnp
set enabled=no allow-disable-external-interface=yes show-dummy-rule=yes
/ ip arp
/ ip socks
set enabled=no port=1080 connection-idle-timeout=2m max-connections=200
/ ip dns
set primary-dns=0.0.0.0 secondary-dns=0.0.0.0 allow-remote-requests=no \
    cache-size=2048KiB cache-max-ttl=1w
/ ip dns static
add name="1" address=202.***.***.*** ttl=1d
add name="2" address=202.***.***.*** ttl=1d
/ ip traffic-flow
set enabled=no interfaces=all cache-entries=4k active-flow-timeout=30m \
    inactive-flow-timeout=15s
/ ip address
add address=172.18.162.27/24 network=172.18.162.0 broadcast=172.18.162.255 \
    interface=lan comment="added by setup" disabled=no
add address=192.168.3.1/24 network=192.168.3.0 broadcast=192.168.3.255 \
    interface=wlan comment="" disabled=no
add address=218.*.***.3/24 network=218.*.***.2 broadcast=218.*.***.9 \
    interface=internat comment="" disabled=no
/ ip proxy
set enabled=no port=8080 parent-proxy=0.0.0.0:0 maximal-client-connecions=1000 \
    maximal-server-connectons=1000
/ ip proxy access
add dst-port=23-25 action=deny comment="block telnet & spam e-mail relaying" \
    disabled=no
/ ip neighbor discovery
set lan discover=yes
set ether2 discover=yes
set internat discover=yes
set wlan discover=yes
/ ip route
add dst-address=172.0.0.0/8 gateway=172.18.162.5 scope=255 target-scope=10 \
    comment="added by setup" disabled=no
add dst-address=0.0.0.0/0 gateway=218.*.***.1 scope=255 target-scope=10 \
    comment="" disabled=no
/ ip firewall mangle
/ ip firewall nat
add chain=srcnat src-address=192.168.2.0/24 dst-address=!192.0.0.0/8 \
    action=masquerade comment="" disabled=no
/ ip firewall connection tracking
set enabled=yes tcp-syn-sent-timeout=5s tcp-syn-received-timeout=5s \
    tcp-established-timeout=1d tcp-fin-wait-timeout=10s \
    tcp-close-wait-timeout=10s tcp-last-ack-timeout=10s \
    tcp-time-wait-timeout=10s tcp-close-timeout=10s udp-timeout=10s \
    udp-stream-timeout=3m icmp-timeout=10s generic-timeout=10m \
    tcp-syncookie=no
/ ip firewall service-port
set ftp ports=21 disabled=no
set tftp ports=69 disabled=no
set irc ports=6667 disabled=no
set h323 disabled=yes
set quake3 disabled=no
set gre disabled=yes
set pptp disabled=yes
/ ip hotspot service-port
set ftp ports=21 disabled=no
/ ip hotspot profile
set default name="default" hotspot-address=0.0.0.0 dns-name="" \
    html-directory=hotspot rate-limit="" http-proxy=0.0.0.0:0 \
    smtp-server=0.0.0.0 login-by=cookie,http-chap http-cookie-lifetime=3d \
    split-user-domain=no use-radius=no
/ ip hotspot user profile
set default name="default" idle-timeout=none keepalive-timeout=2m \
    status-autorefresh=1m shared-users=1 transparent-proxy=yes \
    open-status-page=always advertise=no
/ ip dhcp-server
add name="server1" interface=wlan lease-time=3d address-pool=wlan \
    bootp-support=static add-arp=yes authoritative=after-2sec-delay \
    disabled=no
/ ip dhcp-server config
set store-leases-disk=5m
/ ip dhcp-server network
add address=192.168.3.0/24 gateway=192.168.3.1 dns-server=202.97.***.** \
    comment=""
/ ip ipsec proposal
add name="default" auth-algorithms=sha1 enc-algorithms=3des lifetime=30m \
    lifebytes=0 pfs-group=modp1024 disabled=no
/ ip web-proxy
set enabled=no src-address=0.0.0.0 port=3128 hostname="proxy" \
    transparent-proxy=no parent-proxy=0.0.0.0:0 \
    cache-administrator="webmaster" max-object-size=4096KiB cache-drive=system \
    max-cache-size=none max-ram-cache-size=unlimited
/ ip web-proxy access
add dst-port=23-25 action=deny comment="block telnet & spam e-mail relaying" \
    disabled=no
/ ip web-proxy cache
add url=":cgi-bin \\?" action=deny comment="don't cache dynamic http pages" \
    disabled=no
/ system logging
add topics=info prefix="" action=memory disabled=no
add topics=error prefix="" action=memory disabled=no
add topics=warning prefix="" action=memory disabled=no
add topics=critical prefix="" action=echo disabled=no
/ system logging action
set memory name="memory" target=memory memory-lines=100 memory-stop-on-full=no
set disk name="disk" target=disk disk-lines=100 disk-stop-on-full=no
set echo name="echo" target=echo remember=yes
set remote name="remote" target=remote remote=0.0.0.0:514
/ system upgrade mirror
set enabled=no primary-server=0.0.0.0 secondary-server=0.0.0.0 \
    check-interval=1d user=""
/ system clock dst
set dst-delta=+00:00 dst-start="jan/01/1970 00:00:00" dst-end="jan/01/1970 \
    00:00:00"
/ system watchdog
set reboot-on-failure=yes watch-address=none watchdog-timer=yes \
    no-ping-delay=5m automatic-supout=yes auto-send-supout=no
/ system console
add port=serial0 term="" disabled=no
set FIXME term="linux" disabled=no
set FIXME term="linux" disabled=no
set FIXME term="linux" disabled=no
set FIXME term="linux" disabled=no
set FIXME term="linux" disabled=no
set FIXME term="linux" disabled=no
set FIXME term="linux" disabled=no
set FIXME term="linux" disabled=no
/ system console screen
set line-count=25
/ system identity
set name="MikroTik"
/ system note
set show-at-login=yes note=""
/ system gps
set enabled=no set-system-time=yes
/ system lcd
set enabled=no type=24x4 port=parallel contrast=0
/ system lcd page
set time display-time=5s disabled=yes
set resources display-time=5s disabled=yes
set uptime display-time=5s disabled=yes
set packets display-time=5s disabled=yes
set bits display-time=5s disabled=yes
set version display-time=5s disabled=yes
set wlan display-time=5s disabled=yes
set lan display-time=5s disabled=yes
set ether2 display-time=5s disabled=yes
set internat display-time=5s disabled=yes
set <pppoe-111> display-time=5s disabled=yes
/ system ntp server
set enabled=no broadcast=no multicast=no manycast=yes
/ system ntp client
set enabled=no mode=unicast primary-ntp=0.0.0.0 secondary-ntp=0.0.0.0
/ system routerboard bios
set
/ system health
set state-after-reboot=enabled
/ port
set serial0 name="serial0" baud-rate=9600 data-bits=8 parity=none stop-bits=1 \
    flow-control=hardware
set serial1 name="serial1" baud-rate=9600 data-bits=8 parity=none stop-bits=1 \
    flow-control=hardware
/ ppp profile
set default name="default" use-compression=default use-vj-compression=default \
    use-encryption=default only-one=default change-tcp-mss=yes comment=""
add name="hlw" local-address=hlw remote-address=hlw use-compression=default \
    use-vj-compression=default use-encryption=default only-one=default \
    change-tcp-mss=default dns-server=202.97.***.**,202.97.***.* comment=""
set default-encryption name="default-encryption" use-compression=default \
    use-vj-compression=default use-encryption=yes only-one=default \
    change-tcp-mss=yes comment=""
/ ppp secret
add name="111" service=pppoe caller-id="" password="111" profile=hlw routes="" \
    limit-bytes-in=0 limit-bytes-out=0 comment="" disabled=no
/ ppp aaa
set use-radius=no accounting=yes interim-update=0s
/ queue type
set default name="default" kind=pfifo pfifo-limit=50
set ethernet-default name="ethernet-default" kind=pfifo pfifo-limit=50
set wireless-default name="wireless-default" kind=sfq sfq-perturb=5 \
    sfq-allot=1514
set synchronous-default name="synchronous-default" kind=red red-limit=60 \
    red-min-threshold=10 red-max-threshold=50 red-burst=20 red-avg-packet=1000
set hotspot-default name="hotspot-default" kind=sfq sfq-perturb=5 \
    sfq-allot=1514
add name="default-small" kind=pfifo pfifo-limit=10
/ user
add name="admin" group=full address=***.***.***.***/0 comment="system default user" \
    disabled=no
add name="8*8******" group=full address=***.***.***.***/0 comment="" disabled=no
/ user group
add name="read" policy=local,telnet,ssh,reboot,read,test,winbox,password,web,!f\
    tp,!write,!policy
add name="write" policy=local,telnet,ssh,reboot,read,write,test,winbox,password\
    ,web,!ftp,!policy
add name="full" policy=local,telnet,ssh,ftp,reboot,read,write,policy,test,winbo\
    x,password,web
/ user aaa
set use-radius=no accounting=yes interim-update=0s default-group=read
/ radius incoming
set accept=no port=1700
/ driver
/ snmp
set enabled=no contact="" location=""
/ snmp community
set public name="public" address=0.0.0.0/0 read-access=yes
/ tool bandwidth-server
set enabled=yes authenticate=yes allocate-udp-ports-from=2000 max-sessions=10
/ tool mac-server ping
set enabled=yes
/ tool e-mail
set server=0.0.0.0 from="<>"
/ tool sniffer
set interface=all only-headers=no memory-limit=10 file-name="" file-limit=10 \
    streaming-enabled=no streaming-server=0.0.0.0 filter-stream=yes \
    filter-protocol=ip-only filter-address1=0.0.0.0/0:0-65535 \
    filter-address2=0.0.0.0/0:0-65535
/ tool graphing
set store-every=5min
/ routing ospf
set router-id=0.0.0.0 distribute-default=never redistribute-connected=no \
    redistribute-static=no redistribute-rip=no redistribute-bgp=no \
    metric-default=1 metric-connected=20 metric-static=20 metric-rip=20 \
    metric-bgp=20
/ routing ospf area
set backbone area-id=0.0.0.0 type=default translator-role=translate-candidate \
    authentication=none prefix-list-import="" prefix-list-export="" \
    disabled=no
/ routing bgp
set enabled=no as=1 router-id=0.0.0.0 redistribute-static=no \
    redistribute-connected=no redistribute-rip=no redistribute-ospf=no
/ routing rip
set redistribute-static=no redistribute-connected=no redistribute-ospf=no \
    redistribute-bgp=no metric-static=1 metric-connected=1 metric-ospf=1 \
    metric-bgp=1 update-timer=30s timeout-timer=3m garbage-timer=2m

apaulo

这么多啊 ？学习

shjj8381981

配置：奔腾350，128内存，4g硬盘，ros2.9.27，tp108的无线网卡，interpro100网卡

环境：内网：172.18.162.0/23  网关：172.18.162.5（防火墙做路由） winbox登陆机器：172.18.162.31

外网：218.*.***.**，网关218.*.***.1  网通分配的ip:218.*.***.2~9
dhcp:192.168.2.0/24和192.168.3.0/24两个

试验目的：1、无线网卡接入，dhcp给地址，可以实现nat上互联网
               2、无线网卡接入，dhcp不给地址，进行pppoe后，介入互联网

zooyo

楼主精神可嘉，如果做成动画教程，坛里的不会的朋友肯定更加支持你了！

shjj8381981

我倒是想啊，可是不会用vm啊，哈哈哈

zooyo

。。。。。有空加个QQ交流一下嘛！