还有个问题是，就算弄成功了，但没有那个KEY，也没什么用啊？各位说是不是啊？郁闷....
QUOTE (soft_route @ Aug 4 2004, 09:02 AM)
不用谢！另外不知你的PIX机器带不带软驱的，我在网上看到有些是带软驱的，如果带软驱的话，将你的BIOS用通用的刷写程序备份下来放到网上来，好不好？我想查查BIOS的内容。
不好意思，单位里的pix 515不带软驱，没法备份BIOS．另外，您给的那个82559的EEPROM刷新程序是给intel 82559ER专用的，不能用于一般不带ER的Intel 82559网卡．
刚才又去试了一下，硬件配置：ASUS P2B主板，128MB RAM，WinFast L2300显卡，二块Intel 82557和二块Intel 82559网卡（共四块），Cisco PIX ISA Flash 16MB卡，软驱．先用软盘（内带bh61.bin）启动，console口显示如下：Cisco Secure PIX Firewall BIOS (3.6) Booting Floppy .................................. Cisco Secure PIX Firewall floppy loader (3.0) #0: Tue Sep 11 07:34:46 PDT 2001Reading installation media..............128MB RAMFlash=i28F640J5 @ 0x300BIOS Flash=AT29C257 @ 0xfffd8000----------------------------------------------------------------------- || || || || |||| |||| ..:||||||:..:||||||:.. c i s c o S y s t e m s Private Internet eXchange----------------------------------------------------------------------- Cisco PIX BoothelperCisco PIX Firewall Version 6.1(1)Not enough supported network interface cards installed. PIX requires at least 2 supported interface cards, but only 0 supported interfaces were found.Rebooting....然后就重启了，再用软盘（内带np63.bin）启动，console显示如下：Cisco Secure PIX Firewall BIOS (3.6) Booting Floppy .................................. Cisco Secure PIX Firewall floppy loader (3.0) #0: Thu Jul 17 08:01:07 PDT 2003 Reading installation med Cisco Secure PIX Firewall password tool (3.0) #0: Thu Jul 17 08:01:09 PDT 2003 Flash=i28F640J5 @ 0x300 BIOS Flash=AT29C257 @ 0xd8000 Rebooting.... 再不用软盘，直接从Flash卡启动，console口显示如下：Flash=i28F640J5 @ 0x300 Reading 2028032 bytes of image from flash. 128MB RAM Flash=i28F640J5 @ 0x300 BIOS Flash=AT29C257 @ 0xfffd8000 --------------------------------------------------- || || || || |||| |||| ..:||||||:..:||||||:.. c i s c o S y s t e m s Private Internet eXchange ----------------------------------------------------------------------- Cisco Secure PIX Firewall Cisco Secure PIX Firewall Version 5.2(1) Licensed Features: Failover: Enabled VPN-DES: Enabled VPN-3DES: Disabled Maximum Interfaces: 6 Cut-through Proxy: Enabled Guards: Enabled Websense: Enabled Throughput: Unlimited ISAKMP peers: Unlimited Not enough network interface cards installed. PIX requires at least 2 interface cards, but only 0 interfaces were found. Rebooting....拔下Flash卡，用软盘（内带pix444.bin）启动，console显示如下：Finesse floppy bootstrap (V2.0)PIX floppy loader (3.0) #0: Thu Jan6 16:03:25 PST 2000Reading installation media....................................PIX admin loader (3.0) #0: Thu Jan6 16:03:26 PST 2000No flash device found.hanging...插上Flash卡，用软盘（内带pix444.bin）启动，console显示如下：isco Secure PIX Firewall BIOS (3.6) Booting Floppy .................................. PIX floppy loader (3.0) #0: Thu Jan6 16:03:25 PST Reading installation media.................................... PIX admin loader (3.0) #0: Thu Jan6 16:03:26 PST 2000 Flash=i28F640J5 @ 0x300 Flash version 4.4.4, Install version 4.4.4 Do you want me to install new version onto flash? Noloading from flash... 128MB RAM Flash=i28F640J5 @ 0x300 An internal error occurred.Specifically, a programming assertion wasviolated.Copy the error message exactly as it appears, and get theoutput of the show version command and the contents of the configurationfile.Then call your technical support representative.assertion "ifc < NicCount" failed: file "main.c", line 339mcwa i82557 Ethernet at irq5MAC: 00a0.c948.488fAn internal error occurred.Specifically, a programming assertion wasviolated.Copy the error message exactly as it appears, and get theoutput of the show version command and the contents of the configurationfile.Then call your technical support representative.assertion "ifc < NicCount" failed: file "main.c", line 339mcwa i82557 Ethernet at irq 12MAC: 00a0.c900.b268An internal error occurred.Specifically, a programming assertion wasviolated.Copy the error message exactly as it appears, and get theoutput of the show version command and the contents of the configurationfile.Then call your technical support representative.assertion "ifc < NicCount" failed: file "main.c", line 339系统死机，用flash卡启动，console显示如下：Cisco Secure PIX Firewall BIOS (3.6) Booting Floppy Flash=i28F640J5 @ 0x300 Reading 569856 bytes of image from flash. 128MB RAM Flash=i28F640J5 @ 0x300 An internal error occurred.Specifically, a programming assertion wasviolated.Copy the error message exactly as it appears, and get theoutput of the show version command and the contents of the configurationfile.Then call your technical support representative. assertion "ifc < NicCount" failed: file "main.c", line 339mcwa i82557 Ethernet at irq5MAC: 00a0.c948.488f An internal error occurred.Specifically, a programming assertion wasviolated.Copy the error message exactl as it appears, and get the output of the show version command and the contents of the configuration file.Then call your technical support representative. assertion "ifc < NicCount" failed: file "main.c", line 339mcwa i82557 Ethernet at irq 12MAC: 00a0.c900.b268An internal error occurred.Specifically, a programming assertion wasviolated.Copy the error message exactly as it appears, and get theoutput of the show version command and the contents of the configurationfile.Then call your technical support representative. assertion "ifc < NicCount" failed: file "main.c", line 339系统死机，看来是Flash卡内容被改了，可我在上面是选择no的啊！豁出去了，刷新一下flash试试，用软盘（内带pix444.bin）启动，console显示如下：Booting Floppy .................................. PIX floppy loader (3.0) #0: Thu Jan6 Reading installation media.................................... PIX admin loader (3.0) #0: Thu Jan6 16:03:26 PST 2000 Flash=i28F640J5 @ 0x300 Flash version 4.4.4, Install version 4.4.4 Do you want me to install new version onto flash? Yes Installing to flash Activation Key: xxxxxxx xxxxxxx xxxxxxx xxxxxxxDo you want to enter a new activation key? NoWriting image into flash... 128MB RAM Flash=i28F640J5 @ 0x300 An internal error occurred.Specifically, a programming assertion wasviolated.Copy the error message exactly as it appears, and get theoutput of the show version command and the contents of the configurationfile.Then call your technical support representative.assertion "ifc < NicCount" failed: file "main.c", line 339mcwa i82557 Ethernet at irq5MAC: 00a0.c948.488fAn internal error occurred.Specifically, a programming assertion wasviolated.Copy the error message exactly as it appears, and get theoutput of the show version command and the contents of the configurationfile.Then call your technical support representative.assertion "ifc < NicCount" failed: file "main.c", line 339mcwa i82557 Ethernet at irq 12MAC: 00a0.c900.b268An internal error occurred.Specifically, a programming assertion wasviolated.Copy the error message exactly as it appears, and get theoutput of the show version command and the contents of the configurationfile.Then call your technical support representative.assertion "ifc < NicCount" failed: file "main.c", line 339还是死机，看来得想办法把flash重新刷回高版本的了.....
pix的ROM文件,并不是PC能读取的ROM,因为它不符合BIOS规则(55AA开头),是不是在PIX的主板BIOS中有读取程序?
今天又用cisco原装的网卡（pix-1fe）试了一下，还是不断重启．看来是非得Intel SE440-BX2主板不行了，可这东东现在是不大好找啊！
不对。。的确有朋友用非intel bx成功。。。
386 486 Pentium Pentium III Pentium II Pentium Pro Unknown ModelTC430HX Pentium 133 VS440FX LT430TX PIX-515 PIX-515E PIX-525 PIX-506 PIX-506E AL440LX SE440BX2 PIX-535BIOS Flash=am29f400bBIOS Flash=AT29C257BIOS Flash=e28f400b5tBIOS Flash=I28F256ABIOS Flash=E28F640J3BIOS Flash=e28f400b5tBIOS Flash=DA28F320J5BIOS Flash=AM28F256crt0.o _start _main nploader.o gcc2_compiled. ___gnu_compiled_c _scrub_pw _strncmp _strcat _ffs_open _hang _ffs_write _printf _ffs_close ___main _data_init _duartsa_init _init_a20 _delayinit _pci_init _platform_init ___nploader_version _flash_ldr_init _reboot _ffs_init _ffs_read _flash_secsize _kputs _kgetc _kputc nploader_v.o strncmp.o strcat.o flashfs.o _ffs_currf _ffs_move_file_up _flash_copy_sector ___assert _ffs_move_file_down _ffs_info _ffs_erase_extras _flash_erase_sector _ffs_avail_blocks _flash_size _ffs_overlaps _ffs_file_spacing _ffs_spacecnt _ffs_spacing _ffs_alloc_sectors _ffs_fit_file _ffs_update_header _flash_write _ffs_derive _flash_exec_size _flash_config_size _fdf_find _memset _ffs_versioning _ffs_strata_header_bug _flash_type _flash_read _flashfs _ffs_length_change _ffs_file_bounds _ffs_index _flash_buf_open _flash_buf_close _flash_buf_seek _flash_buf_write _flash_buf_read _ffs_print _ffs_destroy _ffs_downgrade_strata_bug hang.o print.o _fmtconv _noconv _cconv _dconv _hconv _lconv _oconv _sconv _uconv _xconv _percent _inetconv _verconv _fmtindex _donprintf _kprintf _sprintf _numbconv _strconv _strlen __main.o data.o __end __edata duartsa.o _outb _inb _lastc.42 _delay _kgetc_nb _kgets a20.o delay.o _init8259 _cnt_10us pci.o _pci_mode _MaxPCI _outl _inl _pci_regio platform.o _pix_platform _platform_name _platform_mapping _func.38 _platform_old_style _bios_platform _strcmp flashldr.o _flash_init _flash_buffer _flash_set_buffer reboot.o flashstand.o _flash_device _exec_size flash.o _flash_iobase _flash_find _bios_device _biosflash_find _flash_flush _flash_set_addr _flash_info _flash_biosinfo __assert.o flashcfg.o _flash_config_find fdffind.o _memcpy memset.o strlen.o outb.o inb.o outl.o inl.o biosfcns.o _bios_size _bios_ver_tags _bios_plat_tags _bios_base _incr0 _bios_addr _bios_search _memmove _bios_version _bios_id _bios_exists strcmp.o flashfind.o _atmel_present _intel_present _strata_present _strata_read _strata_burn _strata_secsize _strata_flashsize _sfmm_present _sfmm_read _sfmm_burn _sfmm_secsize _sfmm_flashsize exec.o _func.36 _exec_image _exec_old_image biosffind.o _at29c257_present _at29c257_read _at29c257_burn _at29c257_secsize _at29c257_flashsize _am29f400b_present _am29f400b_read _am29f400b_burn _am29f400b_secsize _am29f400b_flashsize _e28f400b5t_present _e28f400b5t_read _e28f400b5t_burn _e28f400b5t_secsize _e28f400b5t_flashsize _am28f256_present _i28f256a_present memcpy.o incr0.o memmove.o atmel.o _atmel_id_entry _atmel_valid_addr _atmel_data_send _atmel_id_exit _atmel_diagnostic _atmel_data_read _chipstat _atmel_sector_size _outw _inw intel.o strata.o _strata_reset _strata_write_enable_pulse _func.42 _strata_ready _strata_status _func.47 _strata_write_buffer_ready _strata_set_addr _strata_send_data _strata_read_word _strata_read_reset _strata_sector_size _func.62 _strata_write_status _func.65 _strata_erase_status _strata_erase _func.70 _splhi _splx _flash_suspend sfmm.o _pmb_gporeg _frameIndex _frame_addr _sfmm_p2l _map_p2l _func.40 _sfmm_ready _sfmm_readstatus _frame_setup _frame_map _sfmm_sector_size _sfmm_chip_size _func.53 _sfmm_write_status _func.56 _sfmm_erase_status _sfmm_erase _func.61 at29c257.o _at29c257_id_entry _at29c257_data_write _at29c257_data_protect_enable _at29c257_id_exit _at29c257_data_read _at29c257_sector_size _at29c257_valid_addr _func.52 am29f400b.o _am29f400b_p2l _am29f400b_ready _am29f400b_sector_size _am29f400b_erase _func.51 e28f400b5t.o _e28f400b5t_p2l _e28f400b5t_ready _e28f400b5t_readstatus _e28f400b5t_sector_size _e28f400b5t_write_status _func.54 _e28f400b5t_erase_status _e28f400b5t_erase _func.59 am28f256.o i28f256a.o outw.o inw.o splhi.o splx.o memmap.o _pci_map_addr _pci_manage_br_conflict __etext _etext __bss_start _edata _end 还有兄弟在关注这个防火墙的破解吗？以上是我从np.bin文件中找出来的，我觉得这些都是关键，估计得找到符合上边条件的硬件才行！
上面的TC430HX、LT430TX、VS440FX、AL440LX、SE440BX2可都是Intel的主板啊！
而事实上部分CISCO的设备就是一台PC，如思科PIX515防火墙，只要你插上一块PCI的显卡到PCI槽，接上显示器，按下PIX的开关，你就可以看到一台BX主板、奔腾II代350MHZ处理器、128M内存电脑的启动信息，和一台普通电脑启动是没有任何区别的。当PIX完成自检后，控制台就转到CONSOLE口上了，而那个RJ45接口的CONSOLE口，其实就是一个COM口，只是接口形式不是9针D形口而己。
找不到上述的Intel主板啊！
估计比较困难.
QUOTE (soft_route @ Aug 21 2004, 02:01 PM)
而事实上部分CISCO的设备就是一台PC，如思科PIX515防火墙，只要你插上一块PCI的显卡到PCI槽，接上显示器，按下PIX的开关，你就可以看到一台BX主板、奔腾II代350MHZ处理器、128M内存电脑的启动信息，和一台普通电脑启动是没有任何区别的。当PIX完成自检后，控制台就转到CONSOLE口上了，而那个RJ45接口的CONSOLE口，其实就是一个COM口，只是接口形式不是9针D形口而己。
支持中，pix515不错。我还没明白固件的编号是怎么pix634.bin是那个机器的？我用他来启动了，搞到我键盘都给锁定了
pix os在各pix硬件中应该是通用的．
关注中。。可惜没有flash卡。。我的启动了就一点点字。。然后没有反应。。连reboot都不
今天搞了一块Intel的AL440LX主板，就搞定了，pix os认作是pix 520．