ros3.30双ADSL PCC负载求助

qinfei

如图：我用单线程下载
第二条线都没有什么流量,下面是脚本：
（V3.24以上版本的PCC功能）
设置lan接口IP与DNS

/ip address add address=172.16.1.1/255.255.255.0 interface=lan comment=lan
/ip dns set primary-dns=202.96.134.133 secondary-dns=202.96.128.68 allow-remote-requests=yes

双线均衡脚本

/ip firewall mangle

add action=change-mss chain=forward comment="" disabled=no new-mss=1400 protocol=tcp tcp-flags=syn

add action=mark-connection chain=input comment="" disabled=no in-interface=pppoe-out1 new-connection-mark=pppoe-out1_conn passthrough=yes

add action=mark-connection chain=input comment="" disabled=no in-interface=pppoe-out2 new-connection-mark=pppoe-out2_conn passthrough=yes

add action=mark-routing chain=output comment="" connection-mark=pppoe-out1_conn disabled=no new-routing-mark=to_pppoe-out1 passthrough=yes

add action=mark-routing chain=output comment="" connection-mark=pppoe-out2_conn disabled=no new-routing-mark=to_pppoe-out2 passthrough=yes

add action=mark-connection chain=prerouting comment="" disabled=no dst-address-type=!local new-connection-mark=pppoe-out1_conn passthrough=yes per-connection-classifier=both-addresses:2/0 src-address=172.16.1.0/24

add action=mark-connection chain=prerouting comment="" disabled=no dst-address-type=!local new-connection-mark=pppoe-out2_conn passthrough=yes per-connection-classifier=both-addresses:2/1 src-address=172.16.1.0/24

add action=mark-routing chain=prerouting comment="" connection-mark=pppoe-out1_conn disabled=no new-routing-mark=to_pppoe-out1 passthrough=yes src-address=172.16.1.0/24

add action=mark-routing chain=prerouting comment="" connection-mark=pppoe-out2_conn disabled=no new-routing-mark=to_pppoe-out2 passthrough=yes src-address=172.16.1.0/24

/ip route

add comment=adsl1 disabled=no distance=1 dst-address=0.0.0.0/0 gateway=pppoe-out1 routing-mark=to_pppoe-out1

add comment=adsl2 disabled=no distance=1 dst-address=0.0.0.0/0 gateway=pppoe-out2 routing-mark=to_pppoe-out2

add check-gateway=ping comment=adsl1 disabled=no distance=10 dst-address=0.0.0.0/0 gateway=pppoe-out1

add check-gateway=ping comment=adsl2 disabled=no distance=10 dst-address=0.0.0.0/0 gateway=pppoe-out2

/ip firewall nat

add action=masquerade chain=srcnat comment="" disabled=no out-interface=pppoe-out1

add action=masquerade chain=srcnat comment="" disabled=no out-interface=pppoe-out2

zooyo

贴规则太抽象了，发截图吧，再仔细看看PCC教程，别邯郸学步，自己试着理解一下原理。

wanken

add action=mark-connection chain=input comment="" disabled=no in-interface=pppoe-out1 new-connection-mark=pppoe-out1_conn passthrough=yes

add action=mark-connection chain=input comment="" disabled=no in-interface=pppoe-out2 new-connection-mark=pppoe-out2_conn passthrough=yes

add action=mark-routing chain=output comment="" connection-mark=pppoe-out1_conn disabled=no new-routing-mark=to_pppoe-out1 passthrough=yes

add action=mark-routing chain=output comment="" connection-mark=pppoe-out2_conn disabled=no new-routing-mark=to_pppoe-out2 passthrough=yes

以上应该不需要吧？？你有读ROS封包的处理规则吗？这几条是要处理ros本机的！


pppoe     gate-way  会变动你没有加如 script 去处理呢！
建议先看懂原理在做！

qinfei

我就是正在理解，我感觉我没理解错，可能是哪个方面（如设置路由或者PPPOE接口）出错了。多谢指教，我想知道ADSL与固定IP的PCC也没多大区别吧？官方只有固定IP的PCC。其实我这个AD脚本是网上下来的。呵呵，这个ADSL双线设置我与官方的固定IP的PCC对比过。没什么特别大的区别。就是PPPOE前面的步骤不太理解。
pppoe     gate-way  会变动，现在不是说新的做法不用script去处理了吗？

那个官方固定IP的PCC我改造过来成ADSL的，老是登不上路由，能上网一段时间就断线了，想不明白，还望赐教。

哎，真菜我

wanken

建議看看我的做法！
http://bbs.routerclub.com/forum. ... &extra=page%3D2

小玩子

qinfei

谢谢各位，我现在搞好了。不用刷新网关的脚本的，呵呵。之前可能是我导太多DSCP和L7的东西进去了，现在不用DSCP了，我宽带足，呵呵

alantang

回复 qinfei 的帖子

分享出来给大家借鉴一下.

qinfei

自己去看吧，我发了
ROS3.30双ADSL PCC负载
http://bbs.routerclub.com/forum. ... &fromuid=129073