NTH多线负载均衡

micke

原来使用ros 2.9x拨多条AD，使用那个牛叉的脚本刷网关，效果不错

现在升级到3.x了，坛子上说不用脚本，直接用INTERFACE，调试也成功，但感觉负载好像不太均衡，每条AD同一时刻流量不像

2.9x里分布均衡，有的线路几M，有的线路才几K，打开网页速度也不如2.9x，请问是哪里问题

配置如下：
/ip firewall mangle
add action=mark-connection chain=prerouting comment=nth_1 connection-state=\
      new disabled=no new-connection-mark=nth_1 nth=5,1 passthrough=yes \
      src-address=192.168.10.0/24
add action=mark-routing chain=prerouting comment="" connection-mark=nth_1 \
      disabled=no new-routing-mark=routing_1 passthrough=yes src-address=\
      192.168.10.0/24

add action=mark-connection chain=prerouting comment=nth_2 connection-state=\
    new disabled=no new-connection-mark=nth_2 nth=5,2 passthrough=yes \
    src-address=192.168.10.0/24
add action=mark-routing chain=prerouting comment="" connection-mark=nth_2 \
    disabled=no new-routing-mark=routing_2 passthrough=yes src-address=\
    192.168.10.0/24

add action=mark-connection chain=prerouting comment=nth_3 connection-state=\
    new disabled=no new-connection-mark=nth_3 nth=5,3 passthrough=yes \
    src-address=192.168.10.0/24
add action=mark-routing chain=prerouting comment="" connection-mark=nth_3 \
    disabled=no new-routing-mark=routing_3 passthrough=yes src-address=\
    192.168.10.0/24

add action=mark-connection chain=prerouting comment=nth_4 connection-state=\
    new disabled=no new-connection-mark=nth_4 nth=5,4 passthrough=yes \
    src-address=192.168.10.0/24
add action=mark-routing chain=prerouting comment="" connection-mark=nth_4 \
    disabled=no new-routing-mark=routing_4 passthrough=yes src-address=\
    192.168.10.0/24

add action=mark-connection chain=prerouting comment=nth_5 connection-state=\
    new disabled=no new-connection-mark=nth_5 nth=5,5 passthrough=yes src-address=\
    192.168.10.0/24
add action=mark-routing chain=prerouting comment="" connection-mark=nth_5 \
    disabled=no new-routing-mark=routing_5 passthrough=yes src-address=\
    192.168.10.0/24

/ip firewall nat
add action=masquerade chain=srcnat comment=1 connection-mark=nth_1 disabled=\
    no out-interface=pppoe-out1
add action=masquerade chain=srcnat comment=2 connection-mark=nth_2 disabled=\
    no out-interface=pppoe-out2
add action=masquerade chain=srcnat comment=3 connection-mark=nth_3 disabled=\
    no out-interface=pppoe-out3
add action=masquerade chain=srcnat comment=4 connection-mark=nth_4 disabled=\
    no out-interface=pppoe-out4
add action=masquerade chain=srcnat comment=5 connection-mark=nth_5 disabled=\
    no out-interface=pppoe-out5


/ip route
add comment="" disabled=no distance=1 dst-address=0.0.0.0/0 gateway=\
    pppoe-out2 routing-mark=routing_2
add comment="" disabled=no distance=1 dst-address=0.0.0.0/0 gateway=\
    pppoe-out3 routing-mark=routing_3
add comment="" disabled=no distance=1 dst-address=0.0.0.0/0 gateway=\
    pppoe-out4 routing-mark=routing_4
add comment="" disabled=no distance=1 dst-address=0.0.0.0/0 gateway=\
    pppoe-out1 routing-mark=routing_1
add comment="" disabled=no distance=1 dst-address=0.0.0.0/0 gateway=\
    pppoe-out5 routing-mark=routing_5
请老大们帮手看看

另外补充点，就是有时候AD断了重拨后有同网关现象，不知道和这个有没有关系，指定接口了应该不会吧？

micke

老大们都不在？ 没人回答的 ，问题太简单不愿回答？

jt00278

这么经典的脚本……