3.xx版自动端口映射 顺便请47771885兄进入

bh

1. {
   
2. #bbs.routerclub.com ID=bh
   
3. :local poe "pppoe-out4";
   
4. /interface pppoe-client;
   
5. monitor $poe once do={
   
6. :if ($status="connected") do={
   
7. :if ($uptime<00:05:00) do={
   
8. :local newIP [/ip address get [/ip address find interface=$poe dynamic=yes] address];
   
9. :set newIP [:pick $newIP 0 [:find $newIP "/"]];
   
10. :put $newIP;
    
11. :local oldIP [/ip fir nat get [/ip fir nat find comment="adsl4_80"] dst-address];
    
12. :if ($newIP!=$oldIP) do={
    
13. :log info [/ip fir nat set [/ip firewall nat find comment="adsl4_80"] dst-address=$newIP];
    
14. :log info ( "adsl4_IP=" . $newIP . " 〖adsl4映射到80端口修改完毕〗");
    
15. }}}}}

复制代码

3.xx版自动端口映射  已在3.20版运行正常，此脚本是根据“47771885”兄的另一脚本修改而来，在此表示感谢!

{
#bbs.routerclub.com ID=bh此为作者备注
:local poe "pppoe-out4";定义需要判断的接口
/interface pppoe-client;
monitor $poe once do={
:if ($status="connected") do={宽带为连接状态时 向下执行脚本
:if ($uptime<00:05:00) do={定义接口连接上多少时间内操作 根据脚本运行间隔时间修改
:local newIP [/ip address get [/ip address find interface=$poe dynamic=yes] address];
:set newIP [:pick $newIP 0 [:find $newIP "/"]];截取指定接口拨号获得的新IP
:put $newIP;
:local oldIP [/ip fir nat get [/ip fir nat find comment="adsl4_80"] dst-address];获取原设映射的旧IP
:if ($newIP!=$oldIP) do={如果新旧IP不相同
:log info [/ip fir nat set [/ip firewall nat find comment="adsl4_80"] dst-address=$newIP];自动填入新IP
:log info ( "adsl4_IP=" . $newIP . " 〖adsl4映射到80端口修改完毕〗");
}}}}}

------------------------------------------------分割线--------------------------------------------------------------
附上2.927版自动端口映射

:global ip [ /ip address get [/ip address find interface=pppoe-out4] address ]
:global new-ip [:pick $ip 0 [:find $ip "/"]]
:global old-ip [/ip fir nat get [/ip fir nat find comment="adsl4_80"] dst-address]
:if ($new-ip != $old-ip) do={
        :log info [/ip fir nat set [/ip firewall nat find comment="adsl4_80"] dst-address=$new-ip]
        :log info "〖adsl4映射到80修改完毕〗"
}

搞出3.xx版，是因为不会把这个2.927版修改成3.xx版，所以另走捷径，呵呵
请问高人该如何改？

47771885

多谢楼上兄弟支持..... 我不是高人 一米七都不到
如果你做映射的话 直接选 接口就好了啊
至于你的这个脚本
吧变量名的- 减号去掉就可以 了
终端运行不支持 直接使用中文 或其他 特殊字符
如

1. {
   
2. :local ip [ /ip address get [/ip address find interface=pppoe-out4] address ]
   
3. :local newip [:pick $ip 0 [:find $ip "/"]]
   
4. :local oldip [/ip fir nat get [/ip fir nat find comment="adsl4_80"] dst-address]
   
5. :if ($newip != $oldip) do={
   
6. :log info [/ip fir nat set [/ip firewall nat find comment="adsl4_80"] dst-address=$newip]
   
7. :log info "\A1\BCadsl4\D3\B3\C9\E4\B5\BD80\D0\DE\B8\C4\CD\EA\B1\CF\A1\BD"
   
8. }}

复制代码

未做详测 有问题 请再说

gll800

还不太会这些~~~