JunoS重新大讨论

cloudq · 发表于 2004-8-27 12:23:45

马上注册，结交更多好友，享用更多功能，让你轻松玩转社区。

您需要登录才可以下载或查看，没有账号？注册

×

最近买了一些新的网卡，，重新安装JUnos，大家有什么问题可以来讨论junos最好要在质量好一些的82557 558 559上装有些质量差的接口起不来。。还有就是最好用freebsd4.7 4.8 4.9mini都可以5.2没研究过。。因为5.2中设备都改名了。。

cloudq · 发表于 2004-8-27 12:28:19

目前正常使用没有问题。。但是nat策略似乎不起作用。。。。。。。。呵呵。。。ids state-firewall还没有测试。。mpls没有环境。。呵呵。。

smile787 · 发表于 2004-8-27 12:41:25

6.2你的起来了吗？5.4的就可以使用。我都是用的inter的好卡

windmail · 发表于 2004-8-27 16:22:00

请问：在那里可以下载？有license吗？急切加入！硬件都准备好了！

cloudq · 发表于 2004-8-27 17:46:49

6。2起来了。。没有问题。。安装后会报一大堆错误。。没有关系commit一下就ok了。。。junos不要lic的。。。

smile787 · 发表于 2004-8-27 18:08:32

QUOTE (windmail @ Aug 27 2004, 04:22 PM)
请问：在那里可以下载？有license吗？急切加入！硬件都准备好了！
论坛的ftp里有，既然cloud兄弟说6.2的可以起来，那么直接用6.2的来玩吧。。。我也就装了一次6.2，可以那里有问题。。。就是没什么时间去玩。

cloudq · 发表于 2004-8-28 08:30:25

好像是6.2默认安装之后由于默认配置里面好像有许多export版本不支持的东西。。所以会报错。。你随便confiugre然后commit rebooot就不会有问题了。。。但是6.2目前还存在一些现实的问题。。。。。。。我配置了set service ids xxxset service nat xxxxset service state-firewall (具体命令可能有出入，我记不清楚了）似乎都没有起作用。。。经过研究junos的技术资料发现fxp口在juniper的设备里面都是manager port真正的fastethernet口不叫fxp所以当你用set interface 命令的时候会发现fxp口没有service 功能set service service-set interface-xxxx 也不能用fxp所以nat ids state-firewall很可能不能做。。也就是说策略上你做了。。但是无法应用到接口。。。这个可能和我用的junos版本有问题。。。。我的show ver之后只有非常少的几个东西。。呵呵。。。。大家有什么发现告诉我呀。。。不过bgp isis mpls,等等高端功能可能没有问题logic-router 也能用。。。具体我会继续测试的。。。。继续讨论

cloudq · 发表于 2004-8-28 08:33:45

看下面的不同Configure the Management Ethernet Interface The routing platform's management Ethernet interface, fxp0, is an out-of-band management interface. You must configure an IP address and prefix length for this interface, which you commonly do when you first install the JUNOS software: [edit]user@host# set interfaces fxp0 unit 0 family inet address/prefix-length[edit]user@host# showinterfaces { fxp0 { unit 0 { family inet { address/prefix-length; } } }}Configure Ethernet Physical Interface Properties To configure Fast Ethernet-specific physical interface properties, include the fastether-options statement at the [edit interfaces fe-fpc/pic/port] hierarchy level: [edit interfaces fe-fpc/pic/port]link-mode (full-duplex | half-duplex);speed (10m | 100m);vlan-tagging;fastether-options { 802.3ad aex; (flow-control | no-flow-control); ingress-rate-limit rate; (loopback | no-loopback); source-address-filter { mac-address; } (source-filtering | no-source-filtering);} The statement speed (10m | 100m) applies only to the management Ethernet interface (fxp0) and to the Fast Ethernet 12-port and 48-port PICs. The 4-port and 8-port Fast Ethernet PICs support a speed of 100 Mbps only.

smile787 · 发表于 2004-8-28 08:50:50

所言极是，少了多口the Fast Ethernet 12-port and 48-port PICs. The 4-port and 8-port Fast Ethernet PICs support a speed of 100 Mbps only.

cloudq · 发表于 2004-8-28 11:57:05

大家别嫌我粘贴的多，，多看这些东西有好处的。。。网吧那些小哥们可能看不下去。。喜欢juniper的朋友可以贴出你们的输出。。。互相研究一下究竟作为fxp的管理口能够应用junos多少的功能root--- JUNOS 6.2R2.4 built 2004-03-19 13:39:35 UTCTerminal type? [vt100] [3g[24;9HH[24;17HH[24;25HH[24;33HH[24;41HH[24;49HH[24;57HH[24;65HH[24;73HHroot@M40% cliroot@M40> show configuration version 6.2R2.4;logical-routers { M10 { interfaces { fxp2 { unit 1 { family inet { address 172.16.100.1/24; } } } } }}system { host-name M40; login { user juniper { uid 2000; class super-user; authentication { encrypted-password "$1$KAwX/fog$cH9hyvokugJlnllbHA1ir0"; # SECRET-DATA---(more)--- } } } services { telnet; }}interfaces { fxp0 { unit 0 { family inet { address 10.37.144.132/21; } } } fxp1 { unit 0 { family inet { filter { input nat; } address 192.168.1.200/24; }---(more 42%)--- } } fxp2 { unit 0 { family inet { address 221.215.40.34/30; } } }}firewall { filter nat { term nat { from { source-address { 192.168.1.0/24; } } then accept; } }}services {---(more 64%)--- stateful-firewall { rule nat { match-direction input; term nat { from { source-address { 192.168.1.0/24; } } then { accept; } } } } nat { pool nat { address 221.215.40.34/32; port automatic; } rule nat { match-direction input; term nat {---(more 85%)--- from { source-address { 192.168.1.0/24; } } then { translated { source-pool nat; translation-type source dynamic; } } } } }}root@M40> show logi og givc ^syntax error, expecting .root@M40> show logivc c ^syntax error, expecting .root@M40> show logic show log run cnf onfigure Entering configuration mode[edit]root@M40# show logical-routers M10 { interfaces { fxp2 { unit 1 { family inet { address 172.16.100.1/24; } } } }}[edit]root@M40# show ver ^syntax error.root@M40# show ver ^syntax error.[edit]root@M40# run show version Hostname: M40Model: oliveJUNOS Base OS boot [6.2R2.4]JUNOS Base OS Software Suite [6.2R2.4]JUNOS Kernel Software Suite [6.2R2.4]JUNOS Packet Forwarding Engine Support (M20/M40) [6.2R2.4]JUNOS Routing Software Suite [6.2R2.4]JUNOS Online Documentation [6.2R2.4][edit]root@M40# exit Exiting configuration moderoot@M40> q request system show interfaces Physical interface: dsc, Enabled, Physical link is Up Interface index: 5, SNMP ifIndex: 5 Type: Software-Pseudo, MTU: Unlimited Device flags : Present Running Interface flags: SNMP-Traps Link flags : None Last flapped : Never Input packets : 0 Output packets: 0Physical interface: fxp0, Enabled, Physical link is Down Interface index: 1, SNMP ifIndex: 1 Type: Ethernet, Link-level type: Ethernet, MTU: 1514, Speed: 10m Device flags : Present Running No-Carrier Interface flags: Hardware-Down SNMP-Traps Link type : Half-Duplex Current address: 00:20:35:e7:c7:67, Hardware address: 00:20:35:e7:c7:67 Last flapped : Never Input packets : 0 Output packets: 0 Logical interface fxp0.0 (Index 64) (SNMP ifIndex 13) Flags: Device-Down SNMP-Traps Encapsulation: ENET2---(more)--- Bandwidth: 0 Input packets : 0 Output packets: 0 Protocol inet, MTU: 1500 Flags: Is-Primary Addresses, Flags: Dest-route-down Is-Default Is-Preferred Is-Primary Destination: 10.37.144/21, Local: 10.37.144.132, Broadcast: 10.37.151.255Physical interface: fxp1, Enabled, Physical link is Down Interface index: 2, SNMP ifIndex: 2 Type: Ethernet, Link-level type: Ethernet, MTU: 1514, Speed: 10m Device flags : Present Running No-Carrier Interface flags: Hardware-Down SNMP-Traps Link type : Half-Duplex Current address: 00:20:35:e7:b2:b1, Hardware address: 00:20:35:e7:b2:b1 Last flapped : Never Input packets : 0 Output packets: 0 Logical interface fxp1.0 (Index 65) (SNMP ifIndex 14) Flags: Device-Down SNMP-Traps Encapsulation: ENET2 Bandwidth: 0---(more 29%)--- Input packets : 0 Output packets: 0 Protocol inet, MTU: 1500 Flags: None Addresses, Flags: Dest-route-down Is-Preferred Is-Primary Destination: 192.168.1/24, Local: 192.168.1.200, Broadcast: 192.168.1.255Physical interface: fxp2, Enabled, Physical link is Down Interface index: 3, SNMP ifIndex: 3 Type: Ethernet, Link-level type: Ethernet, MTU: 1514, Speed: 10m Device flags : Present Running No-Carrier Interface flags: Hardware-Down SNMP-Traps Link type : Half-Duplex Current address: 00:20:35:e7:b2:b6, Hardware address: 00:20:35:e7:b2:b6 Last flapped : Never Input packets : 0 Output packets: 0 Logical interface fxp2.0 (Index 66) (SNMP ifIndex 15) Flags: Device-Down SNMP-Traps Encapsulation: ENET2 Bandwidth: 0 Input packets : 0 ---(more 44%)--- Output packets: 0 Protocol inet, MTU: 1500 Flags: None Addresses, Flags: Dest-route-down Is-Preferred Is-Primary Destination: 221.215.40.32/30, Local: 221.215.40.34, Broadcast: 221.215.40.35Physical interface: gre, Enabled, Physical link is Up Interface index: 129, SNMP ifIndex: 8 Type: GRE, Link-level type: GRE, MTU: Unlimited, Speed: Unlimited Device flags : Present Running Interface flags: Point-To-Point SNMP-Traps Input packets : 0 Output packets: 0Physical interface: ipip, Enabled, Physical link is Up Interface index: 130, SNMP ifIndex: 9 Type: IPIP, Link-level type: IP-over-IP, MTU: Unlimited, Speed: Unlimited Device flags : Present Running Interface flags: SNMP-Traps Input packets : 0 Output packets: 0---(more 59%)--- Physical interface: lo0, Enabled, Physical link is Up Interface index: 6, SNMP ifIndex: 6 Type: Loopback, MTU: Unlimited Device flags : Present Running Loopback Interface flags: SNMP-Traps Link flags : None Last flapped : Never Input packets : 0 Output packets: 0 Logical interface lo0.16383 (Index 68) (SNMP ifIndex 22) Flags: SNMP-Traps Encapsulation: Unspecified Input packets : 0 Output packets: 0 Protocol inet, MTU: Unlimited Flags: NonePhysical interface: lsi, Enabled, Physical link is Up Interface index: 4, SNMP ifIndex: 4 Type: Software-Pseudo, Link-level type: LSI, MTU: 1496, Speed: Unlimited Device flags : Present Running Interface flags: SNMP-Traps Link flags : None---(more 74%)--- Last flapped : Never Input packets : 0 Output packets: 0Physical interface: mtun, Enabled, Physical link is Up Interface index: 133, SNMP ifIndex: 12 Type: Multicast-GRE, Link-level type: GRE, MTU: Unlimited, Speed: Unlimited Device flags : Present Running Interface flags: SNMP-Traps Input packets : 0 Output packets: 0Physical interface: pimd, Enabled, Physical link is Up Interface index: 132, SNMP ifIndex: 11 Type: PIMD, Link-level type: PIM-Decapsulator, MTU: Unlimited, Speed: Unlimited Device flags : Present Running Interface flags: SNMP-Traps Input packets : 0 Output packets: 0Physical interface: pime, Enabled, Physical link is Up Interface index: 131, SNMP ifIndex: 10---(more 89%)--- Type: PIME, Link-level type: PIM-Encapsulator, MTU: Unlimited, Speed: Unlimited Device flags : Present Running Interface flags: SNMP-Traps Input packets : 0 Output packets: 0Physical interface: tap, Enabled, Physical link is Up Interface index: 128, SNMP ifIndex: 7 Type: Software-Pseudo, Link-level type: Interface-Specific, MTU: Unlimited, Speed: Unlimited Device flags : Present Running Interface flags: SNMP-Traps Link flags : None Last flapped : Never Input packets : 0 Output packets: 0root@M40> show interfaces terse Interface Admin Link Proto Local Remotedsc up up fxp0 up downfxp0.0 up down inet 10.37.144.132/21fxp1 up downfxp1.0 up down inet 192.168.1.200/24fxp2 up downfxp2.0 up down inet 221.215.40.34/30gre up up ipip up up lo0 up up lo0.16383 up up inet lsi up up mtun up up pimd up up pime up up tap up up root@M40> conft ^unknown command.root@M40> configure Entering configuration mode[edit]root@M40# set interfaces fx0 p1 unit 0 ?Possible completions: Execute this command accounting-profile Accounting profile name+ apply-groups Groups from which to inherit configuration data+ apply-groups-except Don't inherit configuration data from these groups bandwidth Logical unit bandwidth (informational only) description Text description of the interface disable Disable this logical interface encapsulation Logical link-layer encapsulation> family Protocol family no-traps Don't enable SNMP notifications on state changes passive-monitor-mode Use interface to tap packets from another router traps Enable SNMP notifications on state changes vlan-id Virtual LAN identifier value for 802.1Q VLAN tags | Pipe through a command[edit]root@M40# set interfaces fxp1 unit 0 family inetroot@M40# set interfaces fxp1 unit 0 family inet ?Possible completions: Execute this command> address Interface address/destination prefix+ apply-groups Groups from which to inherit configuration data+ apply-groups-except Don't inherit configuration data from these groups> filter Packet filtering no-redirects Do not redirect traffic> policer Interface policing primary Candidate for primary interface in system | Pipe through a command[edit]root@M40# set interfaces fxp1 unit 0 family inet ?Possible completions:> ccc Circuit cross-connect parameters> inet IPv4 parameters> inet6 IPv6 protocol parameters> iso OSI ISO protocol parameters> mpls MPLS protocol parameters> tcc Translational cross-connect parameters> vpls Virtual Private LAN Service (VPLS) parameters[edit]root@M40# set interfaces fxp1 unit 0 family iso ?Possible completions: Execute this command> address Interface address+ apply-groups Groups from which to inherit configuration data+ apply-groups-except Don't inherit configuration data from these groups | Pipe through a command[edit]root@M40# set interfaces fxp1 unit 0 family iso address ?Possible completions: Interface address[edit]root@M40# set interfaces fxp1 unit 0 family iso address inetroot@M40# set interfaces fxp1 unit 0 family inet ?Possible completions:> inet IPv4 parameters> inet6 IPv6 protocol parameters[edit]root@M40# set interfaces fxp1 unit 0 family inet ?Possible completions: Execute this command> address Interface address/destination prefix+ apply-groups Groups from which to inherit configuration data+ apply-groups-except Don't inherit configuration data from these groups> filter Packet filtering no-redirects Do not redirect traffic> policer Interface policing primary Candidate for primary interface in system | Pipe through a command[edit]root@M40# set interfaces fxp1 unit 0 family inet file ^syntax error.root@M40# set interfaces fxp1 unit 0 family inet file policer ?Possible completions:+ apply-groups Groups from which to inherit configuration data+ apply-groups-except Don't inherit configuration data from these groups input Name of policer applied to received packets output Name of policer applied to transmitted packets[edit]root@M40# set interfaces fxp1 unit 0 family inet policer input ?Possible completions: Name of policer applied to received packets[edit]root@M40# set interfaces fxp1 unit 0 family inet policer input nat ?Possible completions: Execute this command+ apply-groups Groups from which to inherit configuration data+ apply-groups-except Don't inherit configuration data from these groups output Name of policer applied to transmitted packets | Pipe through a command[edit]root@M40# set interfaces fxp1 unit 0 family inet policer input nat ... [edit]root@M40# exit Exiting configuration moderoot@M40> request system reboot Reboot the system ? [yes,no] (no) yes shutdown: [pid 2527]Shutdown NOW!root@M40> *** FINAL System shutdown message from root@M40 *** System going down IMMEDIATELY Jan 16 12:44:55 init: syslogd (PID 2062) exited with status=0 Normal ExitWaiting (max 60 seconds) for system process `bufdaemon' to stop...stoppedWaiting (max 60 seconds) for system process `syncer' to stop...stoppedsyncing disks... 3 3 1 doneUptime: 5m5sata0: Spinning down devices. Please wait...ata2: Spinning down devices. Please wait...Rebooting...Console: serial portBIOS drive C: is disk0BIOS 639kB/261104kB available memoryFreeBSD/i386 bootstrap loader, Revision 0.8(builder@iaculi.juniper.net, Fri Mar 19 13:30:21 GMT 2004)|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\Loading /boot/defaults/loader.conf |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/kernel text=0x496b56 /-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|data=0x2b2f4+0x4b36c /-\|/-\|/-\|/-\|/-\|/-syms=[0x4+0x3f350\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-+0x4+0x4a629\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\] Loader Quick Help ----------------- The boot order is PCMCIA or floppy -> Flash -> Disk -> Lan -> back to PCMCIA or floppy. Typing reboot from the command prompt will cycle through the boot devices. On some models, you can set the next boot device using the nextboot command: nextboot compact-flash | diskFor more information, use the help command: help Hit [Enter] to boot immediately, or space bar for command prompt.Booting [kernel] in 9 seconds... Booting [kernel] in 8 seconds... Booting [kernel] in 7 seconds... Booting [kernel] in 6 seconds... Booting [kernel] in 5 seconds... Booting [kernel] in 4 seconds... Booting [kernel] in 3 seconds... Booting [kernel] in 2 seconds... Booting [kernel] in 1 second... Booting [kernel]... |/-\|/-\Copyright ?1996-2001, Juniper Networks, Inc.All rights reserved.Copyright ?1992-2001 The FreeBSD Project.Copyright ?1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved.JUNOS 6.2R2.4 #0: 2004-03-19 13:39:35 UTC builder@iaculi.juniper.net:/build/iaculi-c/6.2R2.4/obj-i386/sys/compile/JUNIPERTimecounter "i8254" frequency 1193182 HzTimecounter "TSC" frequency 3153726912 HzCPU: Pentium 4 (3153.73-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0xf27 Stepping = 7 Features=0xbfebfbffreal memory = 268419072 (262128K bytes)sio0: gdb debugging portavail memory = 254058496 (248104K bytes)Olive CPUPreloaded elf kernel "kernel" at 0xc0699000.DEVFS: ready for devicesmd0: Malloc disknpx0: on motherboardnpx0: INT 16 interfacepcib0: on motherboardpci0: on pcib0pci0: (vendor=0x8086, dev=0x2551) at 0.1pcib1: mem 0xf4000000-0xf7ffffff at device 1.0 on pci0pci1: on pcib1pci1: at 0.0 irq 11pci0: at 29.0 irq 11pci0: at 29.1 irq 12pci0: at 29.2 irq 10pci0: at 29.7 irq 9pcib2: at device 30.0 on pci0pci2: on pcib2pci2: (vendor=0x1102, dev=0x0002) at 1.0 irq 6pci2: (vendor=0x1102, dev=0x7002) at 1.1fxp0: port 0xb400-0xb41f mem 0xec800000-0xec8fffff,0xf1000000-0xf1000fff irq 9 at device 2.0 on pci2pci2: (vendor=0x14e4, dev=0x4401) at 5.0 irq 10fxp1: port 0xb000-0xb01f mem 0xeb800000-0xeb8fffff,0xf0000000-0xf0000fff irq 5 at device 6.0 on pci2fxp2: port 0xa800-0xa81f mem 0xeb000000-0xeb0fffff,0xef000000-0xef000fff irq 10 at device 7.0 on pci2isab0: at device 31.0 on pci0isa0: on isab0atapci0: port 0xf000-0xf00f,0-0x3,0-0x7,0-0x3,0-0x7 irq 10 at device 31.1 on pci0ata0: at 0x1f0 irq 14 on atapci0fdc0: direction bit not setfdc0: cmd 3 failed at out byte 1 of 3ata2 at port 0x170-0x177,0x376 irq 15 on isa0atkbdc0: at port 0x60,0x64 on isa0atkbd0: flags 0x1 irq 1 on atkbdc0vga0: at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0sc0: at flags 0x100 on isa0sc0: VGA sio0 at port 0x3f8-0x3ff irq 4 flags 0x90 on isa0sio0: type 16550A, consolesio1: configured irq 5 not in bitmap of probed irqs 0sio2 at port 0x2f8-0x2ff irq 3 on isa0sio2: type 16550Asio3: configured irq 7 not in bitmap of probed irqs 0fxp0: Ethernet address 00:20:35:e7:c7:67fxp1: Ethernet address 00:20:35:e7:b2:b1fxp2: Ethernet address 00:20:35:e7:b2:b6DEVFS: ready to runad0: 1547MB [3145/16/63] at ata0-master using PIO3ata2-slave: CDROM device - NO DRIVER!Mounting root from ufs:/dev/ad0s1aMounted jbase package on /dev/vn0...Mounted jkernel package on /dev/vn1...Mounted jpfe package on /dev/vn2...Mounted jdocs package on /dev/vn3...Mounted jroute package on /dev/vn4...swapon: adding /dev/ad0s1b as swap deviceAutomatic reboot in progress.../dev/ad0s1a: FILESYSTEM CLEAN; SKIPPING CHECKS/dev/ad0s1a: clean, 77930 free /dev/ad0s1e: FILESYSTEM CLEAN; SKIPPING CHECKS/dev/ad0s1e: clean, 12110 free (26 frags, 9738 blocks, 0.0% fragmentation)(14 frags, 1512 blocks, 0.1% fragmentation)(26 frags, 9738 blocks, 0.0% fragmentation)/dev/ad0s1f: FILESYSTEM CLEAN; SKIPPING CHECKS/dev/ad0s1f: clean, 932884 free (308 frags, 116572 blocks, 0.0% fragmentation)tunefs: soft updates setCreating initial configuration...mgd: commit completeSetting initial options: debugger_on_panic=NO debugger_on_break=NO.Doing initial network setup:.Initial interface configuration:additional daemons: syslogd.checking for core dump...savecore: Router rebooting after a normal shutdown....Additional routing options:.Doing additional network setup:.Starting final network daemons:.setting ldconfig path: /usr/libstarting standard daemons: cron.Initial rc.i386 initialization: microcode kld.rc.i386 configuring syscons:.Local package initialization:.starting local daemons:.Wed Jan 16 12:46:40 UTC 2002M40 (ttyd0)login: M40 (ttyd0)login: M40 (ttyd0)login: M40 (ttyd0)login: 谢谢大家希望大家提供自己junos的屏幕信息，配置以便于做研究学习

lxw2016 · 发表于 2004-11-24 11:15:59

6.2支持vmwar中的网卡吗

lxw2016 · 发表于 2004-11-28 12:16:10

我装了junos后系统起不来？怎么回事？

zwz2001 · 发表于 2004-11-28 21:19:56

确切的说olive的模式下是不能做nat，ids，状态防火墙的，按照juniper的文档说明这些特征都是在接口卡的流特征处理芯片里面完成，效率很高，juniper牛的地方就是这点了，分布式的流处理方式，所以在olive的模式是不可能有nat命令的。

samhui · 发表于 2004-11-29 16:26:47

好呀。。支持支持支持支持支持支持支持支持支持支持支持支持支持支持!好像比较烦呀，不像cisco的ios

账号		自动登录	找回密码
密码			注册