关于无线ap 的问题 (用卡是Atheros AR5213 )

ly123

问题是   用Atheros AR5213A 的MINI 半高卡 ROS 已经设置成2.4g B/G  没法和.2.4g  的D-LINK 650+ 连接 显示找不到 ap  和别的卡也不行 .这些卡在windos 下都正常. 下面是我的配置文件,望各位指点..!!!谢谢

ROS 2.9.27 wlan 部分配置文件 付件是winbox 的截图

/ interface wireless
set wlan1 name="wlan1" mtu=1500 mac-address=00:02:C7:73:10:F6 arp=enabled disable-running-check=no \
    radio-name="0002C77310F12" mode=ap-bridge ssid="MikroTik" area="" frequency-mode=superchannel country=no_country_set \
    antenna-gain=0 frequency=2312 band=2.4ghz-b/g scan-list=default rate-set=configured \
    supported-rates-b=1Mbps,2Mbps,5.5Mbps,11Mbps \
    supported-rates-a/g=6Mbps,9Mbps,12Mbps,18Mbps,24Mbps,36Mbps,48Mbps,54Mbps basic-rates-b=1Mbps,2Mbps,5.5Mbps,11Mbps \
    basic-rates-a/g=6Mbps,9Mbps,12Mbps,18Mbps,24Mbps,36Mbps,48Mbps,54Mbps max-station-count=2007 ack-timeout=dynamic \
    tx-power-mode=default noise-floor-threshold=default periodic-calibration=default periodic-calibration-interval=60 \
    burst-time=disabled dfs-mode=none antenna-mode=ant-a wds-mode=disabled wds-default-bridge=none wds-default-cost=100 \
    wds-cost-range=50-150 wds-ignore-ssid=no update-stats-interval=disabled default-authentication=yes \
    default-forwarding=yes default-ap-tx-limit=0 default-client-tx-limit=0 proprietary-extensions=post-2.9.25 \
    hide-ssid=no security-profile=default disconnect-timeout=3s on-fail-retry-time=100ms preamble-mode=both \
    compression=no allow-sharedkey=no comment="" disabled=no
/ interface wireless nstreme
set wlan1 enable-nstreme=no enable-polling=yes framer-policy=none framer-limit=3200
/ interface wireless manual-tx-power-table
set wlan1 manual-tx-powers=1Mbps:17,2Mbps:17,5.5Mbps:17,11Mbps:17,6Mbps:17,9Mbps:17,12Mbps:17,18Mbps:17,24Mbps:17,36Mbps:\
    17,48Mbps:17,54Mbps:17
/ interface wireless security-profiles
set default name="default" mode=none authentication-types="" unicast-ciphers="" group-ciphers="" wpa-pre-shared-key="" \
    wpa2-pre-shared-key="" eap-methods=passthrough tls-mode=no-certificates tls-certificate=none static-algo-0=none \
    static-key-0="" static-algo-1=none static-key-1="" static-algo-2=none static-key-2="" static-algo-3=none \
    static-key-3="" static-transmit-key=key-0 static-sta-private-algo=none static-sta-private-key="" \
    radius-mac-authentication=no group-key-update=5m
/ interface wireless align
set frame-size=300 active-mode=yes receive-all=no audio-monitor=00:00:00:00:00:00 filter-mac=00:00:00:00:00:00 \
    ssid-all=no frames-per-second=25 audio-min=-100 audio-max=-20
/ interface wireless connect-list
add interface=wlan1 connect=yes mac-address=00:00:00:00:00:00 ssid="" min-signal-strength=-95 area-prefix="" \
    security-profile=default comment="" disabled=no
/ interface wireless access-list
add mac-address=00:00:00:00:00:00 interface=wlan1 authentication=yes forwarding=yes ap-tx-limit=0 client-tx-limit=0 \
    private-algo=none private-key="" comment="" disabled=no
/ interface wireless snooper
set multiple-channels=yes channel-time=200ms receive-errors=no
/ interface wireless sniffer
set multiple-channels=no channel-time=200ms only-headers=no receive-er

[admin@MikroTik] interface wireless> pr
Flags: X - disabled, R - running
0    name="wlan1" mtu=1500 mac-address=00:02:C7:73:10:F6 arp=enabled
      disable-running-check=no interface-type=Atheros AR5213
      radio-name="0002C77310F12" mode=ap-bridge ssid="MikroTik" area=""
      frequency-mode=superchannel country=no_country_set antenna-gain=0
      frequency=2312 band=2.4ghz-b/g scan-list=default rate-set=configured

xywsk

没有 R 标记呀，无线卡没有运行

dingtian

l连都连接不上，当然没有R标记咯！

专卖精品

有网络连接后才有R标记

zooyo

楼主你发截图吧，而且弄清楚你2张网卡是54M的还是108的!

ly123

附件就是全部的截图  请大家看看!!!  该卡是可以在2.4g  和5g的3频卡. 54和108 的我均试过 不行

zooyo

你直接说，你ROS机器上的无线是多少兆，你客户机上的无线是多少兆

ly123

ros 的速度是适应的方式  (调到过客2.4 B/G 、5G  ）户端用过 22m 54m 108m  的都没连起来

jk2h

frequency=2312 band=2.4ghz-b/g scan-list=default rate-set=configured

试试换个频道：

frequency=2447或者2462

parphy

是两台都是ROS，还是一台是ROS，一台是笔记本？

zooyo

原帖由 jk2h 于 2006-10-31 10:06 发表
frequency=2312 band=2.4ghz-b/g scan-list=default rate-set=configured

试试换个频道：

frequency=2447或者2462

这个才是正确的方法，我问你网卡分布的具体情况，你又答非所问，哎~~如何帮得鸟你！