ipq60xx系列spi启动固件

心想事成

一般ipq6000 ipq6010 ipq6018都是nand 启动。
使用本固件后，从spi启动，可以自动加载引导nand上面的openwrt。

改为spi启动后，就可以不需要编程器直接对nand操作了，砖头因此可以复活了。
将此固件写入w25q32芯片引导就行。
可以支持ipq60xx系列的ax5 ax1800等机器。

启动日志：

[BEGIN] 2025/1/25 23:57:27
ÿ
Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset),  D - Delta,  S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.XF.0.3-00090-IPQ60xxLZB-2
S - IMAGE_VARIANT_STRING=IPQ6018LA
S - OEM_IMAGE_VERSION_STRING=crm-ubuntu47
S - Boot Interface: SPI
S - Secure Boot: Off
S - Boot Config @ 0x000a602c = 0x000002e1
S - JTAG ID @ 0x000a607c = 0x001390e1
S - OEM ID @ 0x000a6080 = 0x00000000
S - Serial Number @ 0x000a4128 = 0x9e959432
S - OEM Config Row 0 @ 0x000a4188 = 0x0000000000000000
S - OEM Config Row 1 @ 0x000a4190 = 0x0000000000000000
S - Feature Config Row 0 @ 0x000a4130 = 0x0000800018200021
S - Feature Config Row 1 @ 0x000a4138 = 0x02c3e83783000009
S - PBL Patch Ver: 1
S - I-cache: On
S - D-cache: On
B -      3413 - PBL, Start
B -       592 - bootable_media_detect_entry, Start
B -      4339 - bootable_media_detect_success, Start
B -      4435 - elf_loader_entry, Start
B -      4607 - auth_hash_seg_entry, Start
B -     10853 - auth_hash_seg_exit, Start
B -     11351 - elf_segs_hash_verify_entry, Start
B -    357527 - elf_segs_hash_verify_exit, Start
B -    361713 - auth_xbl_sec_hash_seg_entry, Start
B -    361859 - auth_xbl_sec_hash_seg_exit, Start
B -    368404 - xbl_sec_segs_hash_verify_entry, Start
B -    368405 - xbl_sec_segs_hash_verify_exit, Start
B -    369334 - PBL, End
B -    295606 - SBL1, Start
B -    438468 - GCC [RstStat:0x0, RstDbg:0x600000] WDog Stat : 0x4
B -    440908 - clock_init, Start
D -      2714 - clock_init, Delta
B -    449387 - boot_flash_init, Start
D -      8784 - boot_flash_init, Delta
B -    461434 - sbl1_ddr_set_default_params, Start
D -       335 - sbl1_ddr_set_default_params, Delta
B -    468083 - boot_config_data_table_init, Start
D -      1952 - boot_config_data_table_init, Delta - (575 Bytes)
B -    477203 - CDT Version:2,Platform ID:8,Major ID:3,Minor ID:2,Subtype:0
B -    482754 - Image Load, Start
D -      6588 - OEM_MISC Image Loaded, Delta - (0 Bytes)
B -    492087 - Image Load, Start
D -      5032 - PMIC Image Loaded, Delta - (0 Bytes)
B -    499956 - sbl1_ddr_set_params, Start
B -    505019 - CPR configuration: 0x366
B -    508130 - Pre_DDR_clock_init, Start
D -       213 - Pre_DDR_clock_init, Delta
D -         0 - sbl1_ddr_set_params, Delta
B -    542717 - Image Load, Start
D -       427 - APDP Image Loaded, Delta - (0 Bytes)
B -    561108 - Image Load, Start
D -       427 - QTI_MISC Image Loaded, Delta - (0 Bytes)
B -    563518 - Image Load, Start
D -       884 - Auth Metadata
D -       641 - Segments hash check
D -     29341 - QSEE Dev Config Image Loaded, Delta - (36498 Bytes)
B -    594750 - Image Load, Start
D -      6679 - Auth Metadata
D -     10400 - Segments hash check
D -    821975 - QSEE Image Loaded, Delta - (1434988 Bytes)
B -   1417152 - Image Load, Start
D -       762 - Auth Metadata
D -       945 - Segments hash check
D -     64172 - RPM Image Loaded, Delta - (102800 Bytes)
B -   1482696 - Image Load, Start
D -       702 - Auth Metadata
D -      3203 - Segments hash check
D -    320433 - APPSBL Image Loaded, Delta - (570200 Bytes)
B -   1831647 - SBL1, End
D -   1536315 - SBL1, Delta
S - Flash Throughput, 1000 KB/s  (2145061 Bytes,  1135265 us)
S - Core 0 Frequency, 800 MHz
S - DDR Frequency, 466 MHz


U-Boot 2016.01 (Jan 25 2025 - 10:11:27 -0500)

DRAM:  smem ram ptable found: ver: 2 len: 4
256 MiB
NAND:  ONFI device found
ID = 1580a1c8
Vendor = c8
Device = a1
qpic_nand: changing oobsize to 64 from 128 bytes
SPI_ADDR_LEN=3
SF: Detected GD25LQ32 with page size 256 Bytes, erase size 4 KiB, total 4 MiB
ipq_spi: page_size: 0x100, sector_size: 0x1000, size: 0x400000
132 MiB
MMC:   <NULL>: 0
PCI0 is not defined in the device tree
In:    serial@78B1000
Out:   serial@78B1000
Err:   serial@78B1000
machid: 8030200
eth0 MAC Address from ART is not valid
eth1 MAC Address from ART is not valid
eth2 MAC Address from ART is not valid
eth3 MAC Address from ART is not valid
eth4 MAC Address from ART is not valid
eth5 MAC Address from ART is not valid
Net:   MAC0 addr:0:3:7f:ba:db:ad
PHY ID1: 0x4d
PHY ID2: 0xd0b1
EDMA ver 1 hw init
Num rings - TxDesc:1 (0-0) TxCmpl:1 (0-0)
RxDesc:1 (15-15) RxFill:1 (7-7)
ipq6018_edma_alloc_rings: successfull
ipq6018_edma_setup_ring_resources: successfull
ipq6018_edma_configure_rings: successfull
ipq6018_edma_hw_init: successfull
eth0
Hit any key to stop autoboot:  0
bootargs=console=ttyMSM0,115200n8 rootfstype=squashfs ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait
Booting from flash
Using nand device 0

---mtdparts_init---
last_ids  :
env_ids   : nand0=nand0
last_parts:
env_parts : mtdparts=nand0:0x4800000@0x3e0000(fs),

last_partition :
env_partition  : <NULL>

---parse_mtdids---
mtdids = nand0=nand0

+ id nand0               134217728 bytes        nand0

---parse_mtdparts---
mtdparts = mtdparts=nand0:0x4800000@0x3e0000(fs),

--- current_save ---
=> partition NULL
--- index partitions ---
=> mtddevnum NULL
=> mtddevname NULL
===device_parse===
--- id_find_by_mtd_id: 'nand0' (len = 5)
entry: 'nand0' (len = 5)
dev type = 2 (nand), dev num = 0, mtd-id = nand0
+ partition: name fs                     size 0x04800000 offset 0x003e0000 mask flags 0
nand0: partition (fs) start offset
nand0: partition (fs)  size : 75497472

total partitions: 1
part_sort_add: list empty
--- index partitions ---
=> mtddevnum NULL
=> mtddevname NULL
===

+ device: nand        0        nand0
--- current_save ---
=> partition nand0,0
--- index partitions ---

--- mtd_part_info: partition number 0 for device nand0 (nand0)
=> mtddevnum 0,
=> mtddevname fs
mtdparts_init: current_mtd_dev  = nand0, current_mtd_partnum = 0
--- find_dev_and_part ---
id = fs
--- find_dev_and_part ---
id = fs
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "mtd=0", size 72 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 576, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 3/1, WL threshold: 4096, image sequence number: 1535487394
ubi0: available PEBs: 0, total reserved PEBs: 576, PEBs reserved for bad PEB handling: 20
Read 0 bytes from volume kernel to 44000000
No size specified -> Using max size (4952064)
## Loading kernel from FIT Image at 44000000 ...
   Using 'config@cp03-c1' configuration
   Trying 'kernel-1' kernel subimage
     Description:  ARM64 OpenWrt Linux-6.1.90
     Type:         Kernel Image
     Compression:  gzip compressed
     Data Start:   0x440000e8
     Data Size:    4860750 Bytes = 4.6 MiB
     Architecture: AArch64
     OS:           Linux
     Load Address: 0x41000000
     Entry Point:  0x41000000
     Hash algo:    crc32
     Hash value:   ec9aa550
     Hash algo:    sha1
     Hash value:   f8a974b98a3cf82aea2e4b380d7fbf041917c6a6
   Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at 44000000 ...
   Using 'config@cp03-c1' configuration
   Trying 'fdt-1' fdt subimage
     Description:  ARM64 OpenWrt xiaomi_rm1800 device tree blob
     Type:         Flat Device Tree
     Compression:  uncompressed
     Data Start:   0x444a2d78
     Data Size:    30610 Bytes = 29.9 KiB
     Architecture: AArch64
     Hash algo:    crc32
     Hash value:   13a5fe93
     Hash algo:    sha1
     Hash value:   ae9cf2d4f99f48bfe91bcae0a0cab9f2c701f817
   Verifying Hash Integrity ... crc32+ sha1+ OK
   Booting using the fdt blob at 0x444a2d78
   Uncompressing Kernel Image ... OK
   Loading Device Tree to 484f5000, end 484ff791 ... OK

---mtdparts_init---
last_ids  : nand0=nand0
env_ids   : nand0=nand0
last_parts: mtdparts=nand0:0x4800000@0x3e0000(fs),
env_parts : mtdparts=nand0:768K@0x0(0:SBL1),128K@0xc0000(0:MIBIB),1664K@0xe0000(0SEE),128K@0x280000(0EVCFG),128K@0x2a0000(0:RPM),128K@0x2c0000(0:CDT),128K@0x2e0000(0:APPSBLENV),640K@0x300000(0:APPSBL),256K@0x3a0000(0:ART),72M@0x3e0000(rootfs)

last_partition : nand0,0
env_partition  : nand0,0

---parse_mtdparts---
mtdparts = mtdparts=nand0:768K@0x0(0:SBL1),128K@0xc0000(0:MIBIB),1664K@0xe0000(0SEE),128K@0x280000(0EVCFG),128K@0x2a0000(0:RPM),128K@0x2c0000(0:CDT),128K@0x2e0000(0:APPSBLENV),640K@0x300000(0:APPSBL),256K@0x3a0000(0:ART),72M@0x3e0000(rootfs)

--- current_save ---
=> partition NULL
--- index partitions ---
=> mtddevnum NULL
=> mtddevname NULL
===device_parse===
--- id_find_by_mtd_id: 'nand0' (len = 5)
entry: 'nand0' (len = 5)
dev type = 2 (nand), dev num = 0, mtd-id = nand0
+ partition: name 0:SBL1                 size 0x000c0000 offset 0x00000000 mask flags 0
nand0: partition (0:SBL1) start offset
nand0: partition (0:SBL1)  size : 786432
+ partition: name 0:MIBIB                size 0x00020000 offset 0x000c0000 mask flags 0
nand0: partition (0:MIBIB) start offset
nand0: partition (0:MIBIB)  size : 131072
+ partition: name 0SEE                 size 0x001a0000 offset 0x000e0000 mask flags 0
nand0: partition (0:QSEE) start offset
nand0: partition (0:QSEE)  size : 1703936
+ partition: name 0EVCFG               size 0x00020000 offset 0x00280000 mask flags 0
nand0: partition (0:DEVCFG) start offset
nand0: partition (0:DEVCFG)  size : 131072
+ partition: name 0:RPM                  size 0x00020000 offset 0x002a0000 mask flags 0
nand0: partition (0:RPM) start offset
nand0: partition (0:RPM)  size : 131072
+ partition: name 0:CDT                  size 0x00020000 offset 0x002c0000 mask flags 0
nand0: partition (0:CDT) start offset
nand0: partition (0:CDT)  size : 131072
+ partition: name 0:APPSBLENV            size 0x00020000 offset 0x002e0000 mask flags 0
nand0: partition (0:APPSBLENV) start offset
nand0: partition (0:APPSBLENV)  size : 131072
+ partition: name 0:APPSBL               size 0x000a0000 offset 0x00300000 mask flags 0
nand0: partition (0:APPSBL) start offset
nand0: partition (0:APPSBL)  size : 655360
+ partition: name 0:ART                  size 0x00040000 offset 0x003a0000 mask flags 0
nand0: partition (0:ART) start offset
nand0: partition (0:ART)  size : 262144
+ partition: name rootfs                 size 0x04800000 offset 0x003e0000 mask flags 0
nand0: partition (rootfs) start offset
nand0: partition (rootfs)  size : 75497472

total partitions: 10
part_sort_add: list empty
--- index partitions ---
=> mtddevnum NULL
=> mtddevname NULL
--- index partitions ---
=> mtddevnum NULL
=> mtddevname NULL
--- index partitions ---
=> mtddevnum NULL
=> mtddevname NULL
--- index partitions ---
=> mtddevnum NULL
=> mtddevname NULL
--- index partitions ---
=> mtddevnum NULL
=> mtddevname NULL
--- index partitions ---
=> mtddevnum NULL
=> mtddevname NULL
--- index partitions ---
=> mtddevnum NULL
=> mtddevname NULL
--- index partitions ---
=> mtddevnum NULL
=> mtddevname NULL
--- index partitions ---
=> mtddevnum NULL
=> mtddevname NULL
--- index partitions ---
=> mtddevnum NULL
=> mtddevname NULL
===

+ device: nand        0        nand0
--- current_save ---
=> partition nand0,0
--- index partitions ---

--- mtd_part_info: partition number 0 for device nand0 (nand0)
=> mtddevnum 0,
=> mtddevname 0:SBL1
mtdparts_init: current_mtd_dev  = nand0, current_mtd_partnum = 0
Could not find PCI in device tree
Using machid 0x8030200 from environment

Starting kernel ...

Jumping to AARCH64 kernel via monitor
[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x51af8014]
[    0.000000] Linux version 6.1.90 (runner@fv-az1146-130) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 11.3.0 r6626-920bcf965) 11.3.0, GNU ld (GNU Binutils) 2.40.0) #0 SMP Thu May 16 11:38:44 2024
[    0.000000] Machine model: Xiaomi RM1800
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000040000000-0x000000004fffffff]
[    0.000000]   DMA32    empty
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000040000000-0x000000004a0fffff]
[    0.000000]   node   0: [mem 0x000000004a100000-0x000000004a4fffff]
[    0.000000]   node   0: [mem 0x000000004a500000-0x000000004a5fffff]
[    0.000000]   node   0: [mem 0x000000004a600000-0x000000004e3fffff]
[    0.000000]   node   0: [mem 0x000000004e400000-0x000000004fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000004fffffff]
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.0
[    0.000000] percpu: Embedded 18 pages/cpu s34536 r8192 d31000 u73728
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: detected: Spectre-v4
[    0.000000] alternatives: applying boot alternatives
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 64512
[    0.000000] Kernel command line: console=ttyMSM0,115200n8 rootfstype=squashfs ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait root=/dev/ubiblock0_1
[    0.000000] Dentry cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
[    0.000000] Inode-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    0.000000] mem auto-init: stackff, heap allocff, heap freeff
[    0.000000] Memory: 176512K/262144K available (7808K kernel code, 870K rwdata, 2220K rodata, 1280K init, 276K bss, 85632K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000]         Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] Root IRQ handler: gic_handle_irq
[    0.000000] GICv2m: range[mem 0x0b00a000-0x0b00affc], SPI[448:479]
[    0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[    0.000000] arch_timer: cp15 and mmio timer(s) running at 24.00MHz (virt/virt).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000001] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.000072] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[    0.000086] pid_max: default: 32768 minimum: 301
[    0.000543] Mount-cache hash table entries: 512 (order: 0, 4096 bytes, linear)
[    0.000556] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes, linear)
[    0.002409] cblist_init_generic: Setting adjustable number of callback queues.
[    0.002417] cblist_init_generic: Setting shift to 2 and lim to 1.
[    0.002618] rcu: Hierarchical SRCU implementation.
[    0.002622] rcu:         Max phase no-delay instances is 1000.
[    0.003269] smp: Bringing up secondary CPUs ...
[    0.003918] Detected VIPT I-cache on CPU1
[    0.004038] CPU1: Booted secondary processor 0x0000000001 [0x51af8014]
[    0.004708] Detected VIPT I-cache on CPU2
[    0.004797] CPU2: Booted secondary processor 0x0000000002 [0x51af8014]
[    0.005427] Detected VIPT I-cache on CPU3
[    0.005514] CPU3: Booted secondary processor 0x0000000003 [0x51af8014]
[    0.005579] smp: Brought up 1 node, 4 CPUs
[    0.005588] SMP: Total of 4 processors activated.
[    0.005593] CPU features: detected: 32-bit EL0 Support
[    0.005598] CPU features: detected: CRC32 instructions
[    0.005662] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
[    0.005668] CPU: All CPU(s) started at EL1
[    0.005671] alternatives: applying system-wide alternatives
[    0.013176] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.013201] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.013428] pinctrl core: initialized pinctrl subsystem
[    0.014596] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.015151] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
[    0.015193] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    0.015242] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[    0.015592] thermal_sys: Registered thermal governor 'step_wise'
[    0.015805] cpuidle: using governor menu
[    0.016136] ASID allocator initialised with 65536 entries
[    0.077951] SCSI subsystem initialized
[    0.078138] usbcore: registered new interface driver usbfs
[    0.078176] usbcore: registered new interface driver hub
[    0.078209] usbcore: registered new device driver usb
[    0.078519] qcom_scm: convention: smc arm 64
[    0.080632] s2: Bringing 0uV into 725000-725000uV
[    0.080698] clocksource: Switched to clocksource arch_sys_counter
[    0.081759] l2: Bringing 0uV into 1800000-1800000uV
[    0.081960] NET: Registered PF_INET protocol family
[    0.082107] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    0.082786] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.082806] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.082821] TCP established hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.082852] TCP bind hash table entries: 2048 (order: 4, 65536 bytes, linear)
[    0.082927] TCP: Hash tables configured (established 2048 bind 2048)
[    0.083145] MPTCP token hash table entries: 256 (order: 0, 6144 bytes, linear)
[    0.083214] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.083238] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.083424] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.083459] PCI: CLS 0 bytes, default 64
[    0.084600] workingset: timestamp_bits=46 max_order=16 bucket_order=0
[    0.089632] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.089645] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.095872] bam-dma-engine 704000.dma-controller: num-channels unspecified in dt
[    0.095887] bam-dma-engine 704000.dma-controller: num-ees unspecified in dt
[    0.100929] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.101615] msm_serial 78b1000.serial: msm_serial: detected port #0
[    0.101651] msm_serial 78b1000.serial: uartclk = 1843200
[    0.101737] 78b1000.serial: ttyMSM0 at MMIO 0x78b1000 (irq = 22, base_baud = 115200) is a MSM
[    0.101766] msm_serial: console setup on port #0
[    0.734072] printk: console [ttyMSM0] enabled
[    0.739203] msm_serial: driver initialized
[    0.748227] loop: module loaded
[    0.749613] Could not find a valid ONFI parameter page, trying bit-wise majority to recover it
[    0.750301] ONFI parameter recovery failed, aborting
[    0.758923] nand: device found, Manufacturer ID: 0xc8, Chip ID: 0xa1
[    0.764002] nand: ESMT NAND 128MiB 1,8V 8-bit
[    0.770319] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    0.788233] i2c_dev: i2c /dev entries driver
[    0.793091] sdhci: Secure Digital Host Controller Interface driver
[    0.793133] sdhci: Copyright(c) Pierre Ossman
[    0.798167] sdhci-pltfm: SDHCI platform and OF driver helper
[    0.804362] remoteproc remoteproc0: releasing cd00000.remoteproc
[    0.810472] NET: Registered PF_INET6 protocol family
[    0.815476] Segment Routing with IPv6
[    0.819298] In-situ OAM (IOAM) with IPv6
[    0.822905] NET: Registered PF_PACKET protocol family
[    0.826848] 8021q: 802.1Q VLAN Support v1.8
[    0.854806] Could not find a valid ONFI parameter page, trying bit-wise majority to recover it
[    0.854956] ONFI parameter recovery failed, aborting
[    0.862409] nand: device found, Manufacturer ID: 0xc8, Chip ID: 0xa1
[    0.867436] nand: ESMT NAND 128MiB 1,8V 8-bit
[    0.873787] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    0.878314] 10 qcomsmem partitions found on MTD device qcom_nand.0
[    0.885507] Creating 10 MTD partitions on "qcom_nand.0":
[    0.891665] 0x000000000000-0x000000180000 : "0:sbl1"
[    0.899118] 0x000000180000-0x0000001c0000 : "0:mibib"
[    0.902841] 0x0000001c0000-0x000000500000 : "0:qsee"
[    0.910513] 0x000000500000-0x000000540000 : "0:devcfg"
[    0.912803] 0x000000540000-0x000000580000 : "0:rpm"
[    0.917736] 0x000000580000-0x0000005c0000 : "0:cdt"
[    0.922709] 0x0000005c0000-0x000000600000 : "0:appsblenv"
[    0.927414] 0x000000600000-0x000000740000 : "0:appsbl"
[    0.933830] 0x000000740000-0x0000007c0000 : "0:art"
[    0.938198] 0x0000007c0000-0x0000097c0000 : "rootfs"
[    0.942021] mtd: partition "rootfs" extends beyond the end of device "qcom_nand.0" -- size truncated to 0x7840000
[    1.057751] mtd: setting mtd9 (rootfs) as root device
[    1.058117] mtdsplit: no squashfs found in "rootfs"
[    1.066550] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 799999 KHz, changing to: 864000 KHz
[    1.068312] remoteproc remoteproc0: cd00000.remoteproc is available
[    1.077845] ubi0: attaching mtd9
[    1.772343] ubi0: scanning is finished
[    1.780583] ubi0: attached mtd9 (name "rootfs", size 120 MiB)
[    1.780626] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    1.785344] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    1.792097] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    1.798947] ubi0: good PEBs: 962, bad PEBs: 0, corrupted PEBs: 0
[    1.805721] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[    1.811972] ubi0: max/mean erase counter: 3/1, WL threshold: 4096, image sequence number: 1535487394
[    1.819004] ubi0: available PEBs: 386, total reserved PEBs: 576, PEBs reserved for bad PEB handling: 20
[    1.828306] ubi0: background thread "ubi_bgt0d" started, PID 341
[    1.829224] block ubiblock0_1: created from ubi0:1(roo򞞠1.853374] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[    1.854014] Freeing unused kernel memory: 1280K
[    1.859629] Run /sbin/init as init process
[    2.486014] init: Console is alive
[    2.486175] init: - watchdog -
[    2.490716] random: crng init done
[    3.638319] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    3.862918] malibu_phy_api_ops_init[2854]:INFO:qca probe malibu phy driver succeeded!
[    3.863131] hsl_phy_phydev_get[798]:ERROR:phy_addr 0 phydev is NULL
[    4.113849] hsl_phy_phydev_get[798]:ERROR:phy_addr 0 phydev is NULL
[    4.114018] hsl_phy_phydev_get[798]:ERROR:phy_addr 0 phydev is NULL
[    4.231114] __adpt_hppe_uniphy_psgmii_mode_set[1115]:INFO:uniphy 0 psgmii channel selection
[    4.455989] regi_init[3989]:INFO:Initializing HPPE Done!!
[    4.456099] regi_init[4049]:INFO:qca-ssdk module init succeeded!
[    4.462802] EDMA ver 1 hw init
[    4.466650] EDMA HW Reset completed succesfully
[    4.469322] Num rings - TxDesc:1 (23-23) TxCmpl:1 (23-23)
[    4.473753] RxDesc:1 (15-15) RxFill:1 (7-7)
[    4.479595] GMAC2(ffffff8000c418c0) Invalid MAC@ - using 36:3b:a4:62:8e:0d
[    4.484510] GMAC3(ffffff80030e18c0) Invalid MAC@ - using 12:73:ae:52:d6:12
[    4.491212] GMAC4(ffffff80030e08c0) Invalid MAC@ - using 92:f9:a8:2a:d4:14
[    4.498031] GMAC5(ffffff80030258c0) Invalid MAC@ - using aa:99:cb:ad:b6:ac
[    4.504866] **********************************************************
[    4.510815] * NSS Data Plane driver
[    4.517294] **********************************************************
[    4.533272] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    4.536170] init: - preinit -
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    9.012309] mount_root: loading kmods from internal overlay
[    9.028295] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[    9.029418] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[    9.246945] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead.
[    9.394824] block: attempting to load /etc/config/fstab
[    9.398856] block: unable to load configuration (fstab: Entry not found)
[    9.398968] block: no usable configuration
[    9.407815] UBIFS (ubi0:2): Mounting in unauthenticated mode
[    9.409802] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 499
[    9.448333] UBIFS (ubi0:2): recovery needed
[    9.553646] UBIFS (ubi0:2): recovery completed
[    9.553746] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data"
[    9.556989] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    9.564912] UBIFS (ubi0:2): FS size: 37711872 bytes (35 MiB, 297 LEBs), max 307 LEBs, journal size 1904640 bytes (1 MiB, 15 LEBs)
[    9.574812] UBIFS (ubi0:2): reserved for root: 1781224 bytes (1739 KiB)
[    9.586425] UBIFS (ubi0:2): media format: w5/r0 (latest is w5/r0), UUID 8359096F-7159-412B-BCFF-FB3881A01194, small LPT model
[    9.596147] mount_root: loading kmods from internal overlay
[    9.619550] kmodloader: loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[    9.620515] kmodloader: done loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[    9.632151] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead.
[    9.670639] block: attempting to load /etc/config/fstab
[    9.670814] block: unable to load configuration (fstab: Entry not found)
[    9.674744] block: no usable configuration
[    9.682726] mount_root: switching to ubifs overlay
[    9.690063] overlayfs: null uuid detected in lower fs '/', falling back to xino=off,index=off,nfs_export=off.
[    9.693539] urandom-seed: Seeding with /etc/urandom.seed
[    9.806751] procd: - early -
[    9.806861] procd: - watchdog -
[   10.098892] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead.
[   10.151162] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead.
[   10.200226] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead.
[   10.252649] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead.
[   10.304418] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead.
[   10.356872] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead.
[   10.407571] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead.
[   10.457284] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead.
[   10.497914] procd: - watchdog -
[   10.511016] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead.
[   10.632881] procd: - ubus -
[   10.652003] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead.
[   10.701857] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead.
[   10.790587] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead.
[   10.898050] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead.
[   10.944819] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead.
[   10.984995] procd: - init -
[   10.993018] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead.
Please press Enter to activate this console.
[   11.121526] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead.
[   11.169691] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead.
[   11.255336] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead.
[   11.302648] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead.
[   11.668613] kmodloader: loading kernel modules from /etc/modules.d/*
[   11.838188] urngd: v1.0.2 started.
[   11.877987] NET: Registered PF_ALG protocol family
[   11.884575] tun: Universal TUN/TAP device driver, 1.6
[   11.904977] cryptodev: driver 1.13 loaded.
[   11.933021] Loading modules backported from Linux version v6.1.24-0-g0102425ac76b
[   11.933060] Backport generated by backports.git v5.15.92-1-44-gd6ea70fafd36
[   11.949012] NET: Registered PF_QIPCRTR protocol family
[   11.959013] xt_time: kernel timezone is -0000
[   11.997759] PPP generic driver version 2.4.2
[   11.998689] PPP MPPE Compression module registered
[   12.002059] NET: Registered PF_PPPOX protocol family
[   12.019070] ath11k c000000.wifi: ipq6018 hw1.0
[   12.019105] ath11k c000000.wifi: FW memory mode: 2
[   12.022760] remoteproc remoteproc0: powering up cd00000.remoteproc
[   12.028235] remoteproc remoteproc0: Booting fw image IPQ6018/q6_fw.mdt, size 7340
[   13.140443] remoteproc remoteproc0: remote processor cd00000.remoteproc is now up
[   13.141717] ath11k c000000.wifi: qmi ignore invalid mem req type 3
[   13.147507] ath11k c000000.wifi: chip_id 0x0 chip_family 0x4 board_id 0xff soc_id 0xffffffff
[   13.153022] ath11k c000000.wifi: fw_version 0x250a04b8 fw_build_timestamp 2021-12-20 07:20 fw_build_id WLAN.HK.2.5.0.1-01208-QCAHKSWPL_SILICONZ-1
[   13.162159] kmodloader: done loading kernel modules from /etc/modules.d/*
[   13.402402] ath11k c000000.wifi: qmi failed to load CAL data file:cal-ahb-c000000.wifi.bin
[   13.402475] ath11k c000000.wifi: failed to load board data file: -12
[   14.814295] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead.
[   19.097084] br-lan: port 1(lan1) entered blocking state
[   19.097139] br-lan: port 1(lan1) entered disabled state
[   19.101429] device lan1 entered promiscuous mode
[   19.114300] br-lan: port 2(lan2) entered blocking state
[   19.114347] br-lan: port 2(lan2) entered disabled state
[   19.118584] device lan2 entered promiscuous mode
[   19.127852] nss-dp 3a001600.dp4 lan3: PHY Link up speed: 1000
[   19.129268] br-lan: port 3(lan3) entered blocking state
[   19.134148] br-lan: port 3(lan3) entered disabled state
[   19.139327] device lan3 entered promiscuous mode
[   19.148404] nss-dp 3a001800.dp5 wan: PHY Link up speed: 1000
[   20.150805] br-lan: port 3(lan3) entered blocking state
[   20.150859] br-lan: port 3(lan3) entered forwarding state
[   20.155098] IPv6: ADDRCONF(NETDEV_CHANGE): wan: link becomes ready
[   20.161175] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready



BusyBox v1.36.0 (2024-05-16 11:38:44 UTC) built-in shell (ash)

     _________
    /        /\      _    ___ ___  ___
   /  LE    /  \    | |  | __|   \| __|
  /    DE  /    \   | |__| _|| |) | _|
/________/  LE  \  |____|___|___/|___|
\        \   DE /
  \    LE  \    /  -------------------------------------------
   \  DE    \  /    OpenWrt SNAPSHOT, r6626-920bcf965
    \________\/    -------------------------------------------


[END] 2025/1/25 23:58:39

lhn1324

感谢分享好东西。