8m 也行~用过～
2.3.1. Soekris EngineeringAll Soekris devices are fully compatible with m0n0wall. For the net4501 and other 45xx models, use the net45xx image. For the net4801, use the net48xx image. Specifications net4501-30: 133 Mhz CPU, 64 Mbyte SDRAM, 3 Ethernet, 2 Serial, CF socket, 1 Mini-PCI socket, 3.3V PCI connector. net4511-30: 100 Mhz CPU, 64 Mbyte SDRAM, 2 Ethernet, 1 Serial, CF socket, 1 Mini-PCI socket, Single PC-Card socket, PoE. net4521-30: 133 Mhz CPU, 64 Mbyte SDRAM, 2 Ethernet, 1 Serial, CF socket, 1 Mini-PCI socket, Dual PC-Card socket, PoE. net4526-20: 100 Mhz CPU, 32 Mbyte SDRAM, 1 Ethernet, 1 Serial, 16 Mbyte CF Flash, 2 Mini-PCI sockets, PoE. net4526-30: 133 Mhz CPU, 64 Mbyte SDRAM, 1 Ethernet, 1 Serial, 64 Mbyte CF Flash, 2 Mini-PCI sockets, PoE. net4801-50: 266 Mhz CPU, 128 Mbyte SDRAM, 3 Ethernet, 2 serial, USB connector, CF socket, 44 pins IDE connector, 1 Mini-PCI socket, 3.3V PCI connector. QUOTE (bow @ Nov 3 2004, 08:53 PM)
网站的说明是大于5M的CF卡。800M以上用-u这个参数，你不是用这个参数了吧。
2.2.3. Storage Mediumm0n0wall will run off of a CompactFlash card, hard drive, or CD with floppy to store the configuration.CompactFlashAt least an 8 MB CompactFlash card is required.Hard DriveAny IDE or SCSI (with supported controller) hard drive will work fine with m0n0wall.CD/floppy setupAny IDE or SCSI (with supported controller) CD-ROM or DVD drive will work with m0n0wall. Also required for this setup is a 1.44 MB floppy drive with blank floppy disk formatted with MS-DOS/FAT file system. Any standard floppy drive will work. For this setup, you must have a PC that supports booting from CD-ROM. 请注意红色字的部分!!! 既然“At least an 8 MB CompactFlash card is required.”那我的不是刚好吗？也能正常写入。就是刚启动时就卡住了。出错信息我试了3种主板，都不同。虽然我现在用一个800M的笔记本硬盘也用了半年了。可是总心疼这个硬盘24X7的开着，用CF卡就不怕，即使坏了就20、30块。net4526-20、net4526-30应该指的是他们具体的两台用做路由的配置。是他们的产品。不是指CF卡的大小吧。 QUOTE
net4526-20: 100 Mhz CPU, 32 Mbyte SDRAM, 1 Ethernet, 1 Serial, 16 Mbyte CF Flash, 2 Mini-PCI sockets, PoE.
为什么这里只用一块网卡的？如果是这样理论上我现在那台P200+48M也能用MONO 经过我的测试请你换24M以上的CF卡马上就好了我测试过的要是8M能写的话我也不会在这里发帖子了或者你可以用U盘试试也很不错的还有请问moran321你用的是什么牌子的CF卡？用的是什么接口的？请你用USB接口的CF卡写可以吗？？？？？？？？？？？？？？？？？ 刚才看见了MONO的邮件通知马上要出1.2正式版了本来今晚打算写MONO完全安装配置教程的看见邮件里通知说1.2正式版会有很大的改进！（不如说禁PING！因为MONO根本无法禁PING的！）所以还是请大家耐心等待！个人感觉MONO的防火墙一直都做的不好这次32M的1.2正式版不知道会是什么样子呢？ Installation on a standard PC (CF/IDE version)Alternative installation method with Damn Small LinuxInstallation on a standard PC requires the following steps:download the raw CF/IDE image (generic-pc) write the image to a CF card (> 5 MB) or an IDE hard disk, either with dd under FreeBSD or under Windows with my tool, physdiskwrite 0.5 FreeBSD:gzcat generic-pc-xxx.img | dd of=/dev/rad bs=16kwhere n = the ad device number of your CF card (check dmesg)(ignore the warning about trailing garbage - it's because of the digital signature) Linux:gunzip -c generic-pc-xxx.img | dd of=/dev/hdX bs=16kwhere X = the IDE device name of your HD/CF card (check with hdparm -i /dev/hdX) - some CF adapters, particularly USB, may show up under SCSI emulation as /dev/sdX(ignore the warning about trailing garbage - it's because of the digital signature) Windows:(use the -u flag if the target disk is > 800 MB - make very sure you've selected the right disk!!)physdiskwrite [-u] generic-pc-xxx.img(you must use v0.3 or later!) put the CF card/HD into the target PC plug the PC into the network (LAN/WAN/...) power it up assign functions (LAN/WAN/OPT) to your interfaces (hint: use auto-detection, or let the MAC addresses tell you which card is which one) change the LAN IP address, or use the default (192.168.1.1; m0n0wall acts as a DHCP server by default) access the webGUI (user: 'admin', default password: 'mono') make the necessary changes to the default configuration net4801Soekris Engineering 是这个吧，这个不是普通PC
页:
[1]
2