louis_2003
发表于 2004-8-15 12:50:58
原来用软盘作的Coyote动不动软盘就坏了，主要是在加载linux的时候那两个文件太大的。比较难读！把那些要读的文件放到光盘里边，而软盘里边保留配置文件就好了，这样启动很顺利！
louis_2003
发表于 2004-8-15 12:51:28
而且设置还可以保留!
刘朋
发表于 2004-8-15 16:25:23
你也是说说具体怎么弄啊？
DreamCat
发表于 2004-8-15 18:13:56
麻烦，不如用DOM 或 FLASH 卡呢
louis_2003
发表于 2004-8-16 00:09:04
那东西要从新买啊我现在用的这个东西就是以前的老东西剩下来的啊一个DOM起码要用到150以上吧况且你要是想用光驱或者软驱的时候直接拔就可以了先把电源线拔了然后再把数据线拔了就OK了经常这样拔没有出什么问题
xieganhui
发表于 2004-8-19 15:06:48
出自http://www.rictec.com.br/claudio/coyote/bootcd.htmHow to Make a Coyote Linux Bootable CD Why to do that?- You might have your own reasons. I think to put Coyote Linux in a CD is a very bad idea.What do you need?- A Working Coyote LInux 2.10 or above floppy.- A Coyote Linux kernel compiled with IDE and CD-ROM support enabled (Download it here)- A blank CD-R- A good software to burn your bootable CD. In this document I used Nero - Burning Rom.Step 0 - Understanding what we will makeAny good cd-rom burning software can make a bootable cd by taking a image of a boot floppy. When this cd is used the floppy image will be used by some kind of floppy emulator. However Coyote can't read its package files from this image so we have to include the .tgz files to the root of cd-rom too and we have to add the ability to read this cd to the kernel of Coyote.The only .tgz file that will be read from floppy image is the root.tgz all other packages will be read from cd root, so if you want to add any additional packages to coyote they don't need to be on floppy just place then on cd compilation.Very Important: You will NOT be able to backup any change to your Coyote configurations after the cd is burned. Be sure you Coyote floppy is working and you have configured everything you want.Step 1 - Preparing you floppy to take its image- Make a good backup of your floppy before you start- Download the IDE and CD-ROM enabled kernel (linux-210-cdrom), rename it to linux and replace this file at floppy.- edit the file a:\syslinux.cfg. Navigate to the end of fourth line. You will find something like boot=/dev/fd0,vfat. Replace that with boot=/dev/hdc,iso9660- Save the file and close the editor.Note:/dev/hdc means your CD drive is installed as Secondary - Master. You can change it to choose your correct IDE interface:Primary Master = hdaPrimary Slave = hdbSecondary Master = hdcSecondary Slave = hddStep 2 - Burning the CD- Insert your just prepared Coyote Boot Floppy to the drive.- Open Nero and start a new compilation. Choose CD-ROM (Boot).- On tab-page Boot check the option Bootable logical drive. Uncheck the option Enable expert settings.- Click the New button.- From the right panel (File Browser) select the floppy drive, select all the files on this folder then drag and drop them to the left panel.- If you want add any add-on to coyote it's time to add them to the left panel.- Burn your cd.
页:
[1]